7N8651 SUPPORT AS Caterpillar parts
3512B, 3516, 3516B, 3516C, G3516, G3516B
Rating:
Alternative (cross code) number:
CA7N8651
7N-8651
7N8651
CA7N8651
7N-8651
7N8651
Weight: 371 pounds 168 kg.
GAS ENGINE, MARINE ENGINE,
Compatible equipment models: 7N8651:
Information:
The normal engine oil change interval is listed in this Operation and Maintenance Manual, "Maintenance Interval Schedule".Abnormally harsh operating cycles or harsh environments can shorten the service life of the engine oil. Arctic temperatures, corrosive environments, or dusty conditions may require a reduction in engine oil change intervals. Also refer to Special Publication, SEBU5898, "Cold-Weather Recommendations for All Caterpillar Machines". Poor maintenance of air filters or of fuel filters requires reduced oil change intervals. Consult your Caterpillar dealer for more information if this product will experience abnormally harsh operating cycles or harsh environments.Adjustment of the Oil Change Interval
Note: Your Caterpillar dealer has additional information on these programs.Cat oil filters are recommended.Program A
Verification for an Oil Change Interval of 500 HoursThis program consists of three oil change intervals of 500 hours. Oil sampling and analysis are done at 250 hours and 500 hours for each of the three intervals for a total of six oil samples. The analysis includes oil viscosity and infrared (IR) analysis of the oil. If all the results are satisfactory, the 500-hour oil change interval is acceptable for the machine in that application. Repeat Program A if you change the application of the machine.If a sample does not pass the oil analysis, take one of these actions:
Shorten the oil change interval to 250 hours.
Proceed to Program B.
Change to a preferred oil type in the “Lubricant Viscosities for Ambient Temperatures” Table in this Operation and Maintenance ManualProgram B
Optimizing Oil Change IntervalsBegin with a 250-hour oil change interval. The oil change intervals are adjusted by increments. Each increment is an extra 50 hours. Periodic oil sampling and analysis are done during each interval. The analysis includes oil viscosity and infrared (IR) analysis of the oil. Repeat Program B if you change the application of the machine.If an oil sample does not pass the analysis, shorten the oil change interval, or change to a preferred multigrade oil type in the listing above.References
Reference: Special Publication, SEBU6250, "Caterpillar Machine Fluids Recommendations"Reference: Special Publication, SEBU5898, "Cold-Weather Recommendations for All Caterpillar Machines"Reference: Special Publication, PEDP7035, "Optimizing Oil Change Intervals"Reference: Special Publication, PEDP7036, "S O S Fluid Analysis"Reference: Special Publication, PEDP7076, "Understanding the S O S Oil Analysis Tests"Procedure for Changing the Engine Oil and Filter
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
The engine oil drain valve is positioned on the left-hand side of the engine oil pan behind the rear axle. The engine oil pan is located above the engine bottom guard (if equipped).
Illustration 1 g02830157
(1) Engine oil drain valve access cover
(2) Engine oil drain valve hose
The engine oil drain valve can be reached through the access opening in the
Note: Your Caterpillar dealer has additional information on these programs.Cat oil filters are recommended.Program A
Verification for an Oil Change Interval of 500 HoursThis program consists of three oil change intervals of 500 hours. Oil sampling and analysis are done at 250 hours and 500 hours for each of the three intervals for a total of six oil samples. The analysis includes oil viscosity and infrared (IR) analysis of the oil. If all the results are satisfactory, the 500-hour oil change interval is acceptable for the machine in that application. Repeat Program A if you change the application of the machine.If a sample does not pass the oil analysis, take one of these actions:
Shorten the oil change interval to 250 hours.
Proceed to Program B.
Change to a preferred oil type in the “Lubricant Viscosities for Ambient Temperatures” Table in this Operation and Maintenance ManualProgram B
Optimizing Oil Change IntervalsBegin with a 250-hour oil change interval. The oil change intervals are adjusted by increments. Each increment is an extra 50 hours. Periodic oil sampling and analysis are done during each interval. The analysis includes oil viscosity and infrared (IR) analysis of the oil. Repeat Program B if you change the application of the machine.If an oil sample does not pass the analysis, shorten the oil change interval, or change to a preferred multigrade oil type in the listing above.References
Reference: Special Publication, SEBU6250, "Caterpillar Machine Fluids Recommendations"Reference: Special Publication, SEBU5898, "Cold-Weather Recommendations for All Caterpillar Machines"Reference: Special Publication, PEDP7035, "Optimizing Oil Change Intervals"Reference: Special Publication, PEDP7036, "S O S Fluid Analysis"Reference: Special Publication, PEDP7076, "Understanding the S O S Oil Analysis Tests"Procedure for Changing the Engine Oil and Filter
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
The engine oil drain valve is positioned on the left-hand side of the engine oil pan behind the rear axle. The engine oil pan is located above the engine bottom guard (if equipped).
Illustration 1 g02830157
(1) Engine oil drain valve access cover
(2) Engine oil drain valve hose
The engine oil drain valve can be reached through the access opening in the
Cat SIS web machinery list:
Parts support Caterpillar catalog:
3299300
SUPPORT AS
G3512B, G3516, G3516B, G3520B
G3512B, G3516, G3516B, G3520B
3282619
SUPPORT AS
G3516, G3516B, G3520B
G3516, G3516B, G3520B
3267928
SUPPORT
G3516, G3516B, G3520B
G3516, G3516B, G3520B
3282613
SUPPORT AS
G3512B, G3516, G3516B, G3520B
G3512B, G3516, G3516B, G3520B
7W3903
SUPPORT AS
3508, 3512, 3516, G3512, G3516
3508, 3512, 3516, G3512, G3516
2625580
SUPPORT AS
G3512, G3516
G3512, G3516
2520161
SUPPORT AS
3516B
3516B
2520162
SUPPORT AS
3516B
3516B
3077364
SUPPORT
G3512, G3516
G3512, G3516
3083824
SUPPORT
G3512, G3516
G3512, G3516
3394386
SUPPORT AS
G3516B
G3516B
8N2002
SUPPORT
3516
3516
7E3821
SUPPORT AS
3516, 3516B
3516, 3516B
7W7996
SUPPORT AS
3516
3516
1W9295
SUPPORT AS
3516
3516
4P3307
SUPPORT-OUTER
3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C
3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C
7L7857
SUPPORT AS-CLUTCH
3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, D348, D399
3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, D348, D399
7C9917
SUPPORT AS-ENGINE
3114, 3116, 3126, 3126B, C7
3114, 3116, 3126, 3126B, C7
7W4420
SUPPORT-SHAFT
214B, 3114, 3116, IT28F
214B, 3114, 3116, IT28F
7W4374
SUPPORT-SHAFT
214B, 3114, 3116, IT28F
214B, 3114, 3116, IT28F
7N8655
SUPPORT AS
3516
3516
7N8654
SUPPORT AS
3516
3516
7N8652
SUPPORT AS
3512B, 3516, 3516B, 3516C, G3516, G3516B
3512B, 3516, 3516B, 3516C, G3516, G3516B