AVSPARE.COM
parts catalog

SWITCH - PUSH PULL 0871775 - Caterpillar


0871775 SWITCH - PUSH PULL Caterpillar parts AD40, AD45, AD55, AE40, AE40 II, AP-1050, D250D, D300D, PM-565, R1300, R1600, R1700 II, R1700G, R2900
Rating:
43
Alternative (cross code) number:
CA0871775
087-1775
0871775
Caterpillar 0871775 SWITCH - PUSH PULL
Weight: 0.25 pounds 0 kg.

Buy SWITCH - PUSH PULL 0871775 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK, UNDERGROUND ART TRUCK,

Compatible equipment models: 0871775:

ARTICULATED TRUCK  D250D   D300D  
ASPHALT PAVER  AP-1050  
COLD PLANER  PM-565  
LOAD HAUL DUMP  R1300   R1600   R1700 II   R1700G   R2900  
UNDERGROUND ART TRUCK  AD40   AD45   AD55   AE40   AE40 II   Caterpillar
Number on catalog scheme: 15
  For full view, you need register

Information:


Illustration 1 g00788933
Schematic of the work tool solenoidThis procedure is used when the solenoid valve that controls the work tool does not operate correctly, and there are no active diagnostic codes.Test Step 1. CHECK FOR POWER
Turn the key start switch to the OFF position.
Disconnect the machine harness connector at the foot switch for the work tool.
Turn the key start switch to the ON position.
At the main relay, measure the voltage from wire 308-YL to wire 200-BK.Expected Result:The voltage is 18 to 24 DCV.Results:
The voltage is 18 to 24 DCV. The circuit for the key start switch is correct. - Proceed to Test Step 2.
The voltage is not 18 to 24 DCV. There is a problem with the circuit for the key start switch. - Repair: Troubleshoot the starting system. Go to Testing and Adjusting, RENR3814, "No Power Supply To Controller - Troubleshoot" Stop.Test Step 2. CHECK THE WIRING HARNESS FOR THE FOOT SWITCH
At the machine harness connector for the foot switch, measure the voltage between contact 1 and frame ground.Note: The electrical system schematic refers to the foot switch as "ATCH HAMMER FOOT SW".Expected Result:The voltage measurement is 18 to 24 DCV.Results:
The voltage is 18 to 24 DCV. The + battery circuit for the foot switch is correct. - Proceed to Test Step 3.
The voltage is not 18 to 24 DCV. The + battery circuit for the foot switch has failed. - Repair: Replace the machine harness or repair the machine harness. Stop.Test Step 3. CHECK THE FOOT SWITCH
The machine harness remains disconnected from the foot switch.
At the harness connector for the foot switch, measure the resistance from contact 1 to contact 2. Note the resistance and press the foot switch. Measure the resistance again.Expected Result:The resistance changes from less than 5 ohms to being greater

Caterpillar parts catalog:

Caterpillar parts catalog
AP-1050 Asphalt Paver 1JG00001-UP (MACHINE) POWERED BY 3116 Engine
PM-565 Cold Planer 3TK00001-00112 (MACHINE) POWERED BY 3408 Engine
AD40 UNDERGROUND ARTICULATED TRUCK 1YZ00001-UP (MACHINE)
AE40 UNDERGROUND ARTICULATED TRUCK 1ZZ00001-UP (MACHINE)
AD45 UNDERGROUND ARTICULATED TRUCK BKZ00181-UP (MACHINE)
AD55 UNDERGROUND ARTICULATED TRUCK ANW00001-UP (MACHINE)
AE40 SERIES II UNDERGROUND ARTICULATED TRUCK BLW00181-UP (MACHINE)


Parts switch Caterpillar catalog:

9W3187 SWITCH AS-PRESSURE
120G, 12G, 12H ES, 12H NA, 130G, 140G, 140H ES, 140H NA, 143H, 14G, 160G, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 578, 589, 613C, 615C, 621E, 621F, 623E, 627E, 627F, 631E, 637E, 651E, 657E, 768C, 769C...
3D9718 SWITCH (push)
10 FT, 10-20B, 10B, 120, 12E, 140, 14E, 16, 16G, 206, 212, 214B, 215, 224B, 225, 227, 235, 245, 518C, 528B, 530B, 615, 621B, 621R, 623, 627, 627B, 631C, 637, 637D, 641B, 657, 657B, 666, 666B, 8 FT, 8-...
7N9785 SWITCH-TEMPERATURE
120G, 12G, 12H ES, 12H NA, 130G, 140G, 140H ES, 140H NA, 143H, 14G, 160G, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 245D, 578, 589, 611, 613C, 615, 615C, 621E, 621F, 623E, 627E, 627F, 631E, 637E, 651E, ...
3E9350 SWITCH AS-TEMPERATURE
2384C, 2484C, 515, 517, 525, 527, 559C, 561M, 579C, 583R, 587R, 789B, 826C, 836, CB-214D, CB-214E, D10R, D11R, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D6H, D6H XL, D6H XR, D6M, D7H, D8R,...
3E7692 SWITCH AS-PRESSURE
525B, 535B, 725, 730, 735, 740, 924G, 924GZ, 953C, 963B, 963C, D5M, D6M, IT28G, R1600, R1600G, R1700 II, R1700G, R2900G, R3000H
1V7362 SWITCH ASSEM. (wiper)
120G, 130G, 16G, 518, 615, 815B, 826C, 834B, 941, 943, 950B, 955L, 963, 966D, 980C, 988B, 992C, D10, D4E, D5B, D6D, D7G, R1700 II
1056117 SWITCH AS-LIMIT
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725C, 730C, 735B, 740B, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, ...
1056118 SWITCH AS-LIMIT
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 814F, 815F, 816F, 824G, 825G, 826G, 918F, 924F, 938F, 950F, 950F II, 950G, 960F, 962G, 966F, 966F II, 966G, 970F, 972G, 980G, IT18F, IT24F, IT28...
2284808 SWITCH GP-POSITION
770, 770G, 770G OEM, 772, 772G, 772G OEM, 773E, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777D, 777F, 777G, AD30, AD45B, AD55, AD55B, AD60
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.