0993955 SWITCH AS Caterpillar parts
311, 312, 320, 320 L, 320N, E110B, E120B, E200B
Rating:
Alternative (cross code) number:
CA0993955
099-3955
0993955
CA0993955
099-3955
0993955
Weight: 2 pounds 1 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 0993955 Starter Solenoid Switch
CTP Sold as each || Highly Efficient || Easy in-and-out fit
CTP Sold as each || Highly Efficient || Easy in-and-out fit
CTP 0993955 Starter Solenoid Switch
CTP Sold as each || Highly Efficient || Easy in-and-out fit
CTP Sold as each || Highly Efficient || Easy in-and-out fit
Number on catalog scheme:
10
For full view, you need register
Compatible equipment models: 0993955:
Information:
Removal Procedure
Start By:
Remove the lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
If the engine is equipped with a mechanical fuel transfer pump, remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Remove and Install".
Illustration 1 g01311407
Typical example
Illustration 2 g01311411
Typical example
Remove slider (3) from camshaft gear (4). Note: C0.5, C0.7, C1.1, and C1.6 engines have a different camshaft retainer and different fasteners to C1.5 and C2.2 engines. The removal procedure is similar for all models.
Rotate camshaft gear (4) in order to align the access hole in the camshaft gear with fastener (2). For C0.5, C0.7, C1.1, and C1.6 engines, remove allen head screw (2) and remove bolt (1).For C1.5 and C2.2 engines, remove bolt (2). Rotate camshaft gear (4) in order to align the access hole in the camshaft gear with bolt (1). Remove bolt (1).
Remove camshaft retainer (5).
Rotate the crankshaft until timing marks (X) are aligned on the following gears:
Crankshaft gear (7)
Camshaft gear (4)
Idler gear (6)
Illustration 3 g01311416
Typical example
Carefully remove camshaft assembly (8) from the cylinder block. Note: Ensure that the lobes of the camshaft and the camshaft bearings are not damaged.
Start By:
Remove the lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
If the engine is equipped with a mechanical fuel transfer pump, remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Remove and Install".
Illustration 1 g01311407
Typical example
Illustration 2 g01311411
Typical example
Remove slider (3) from camshaft gear (4). Note: C0.5, C0.7, C1.1, and C1.6 engines have a different camshaft retainer and different fasteners to C1.5 and C2.2 engines. The removal procedure is similar for all models.
Rotate camshaft gear (4) in order to align the access hole in the camshaft gear with fastener (2). For C0.5, C0.7, C1.1, and C1.6 engines, remove allen head screw (2) and remove bolt (1).For C1.5 and C2.2 engines, remove bolt (2). Rotate camshaft gear (4) in order to align the access hole in the camshaft gear with bolt (1). Remove bolt (1).
Remove camshaft retainer (5).
Rotate the crankshaft until timing marks (X) are aligned on the following gears:
Crankshaft gear (7)
Camshaft gear (4)
Idler gear (6)
Illustration 3 g01311416
Typical example
Carefully remove camshaft assembly (8) from the cylinder block. Note: Ensure that the lobes of the camshaft and the camshaft bearings are not damaged.
Caterpillar parts catalog:
Parts switch Caterpillar catalog:
1090, 1190, 1190T, 120, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H,...
10 FT, 10-20B, 10B, 311, 312, 315, 317, 320, 320 L, 3208, 320N, 322, 325, 325 LN, 330, 330 L, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 3456, 350, 3508, 3508B, 350...
120G, 12G, 130G, 140G, 14G, 160G, 16G, 215D, 225, 225D, 229, 229D, 231D, 235C, 235D, 245B, 245D, 311, 312, 315, 315B, 315B FM L, 317, 320 L, 320B, 320B FM LL, 320B L, 322 FM L, 322B, 322B L, 322B LN, ...
311F LRR, 312E, 312E L, 315, 315B, 315B FM L, 315C, 315D L, 316E L, 317B LN, 318B, 318E L, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320...
311B, 312, 312B, 312B L, 312C, 312C L, 315, 315B, 315B FM L, 315B L, 315C, 317, 317B LN, 318B, 318C, 320B, 320B FM LL, 320C, 320C FM, 320N, 321B, 322, 322B, 322B LN, 322C, 322C FM, 325B, 325B L, 325C,...
311, 311B, 3126B, 312B, 312C, 312C L, 313B, 314C, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 318C, 319C, 320 L, 3208, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320N, 321B, 322, 322 FM L, 325, 325 L, 32...
307, 311, 312, 315, 317, 320 L, 320N, 322, 322 FM L, 322 LN, 325, 330, 330 L, 350 L, 375, 5080
311, 312, 315, 317, 322, 322 FM L, 322 LN, 325 L, 330 L
311, 312, 315, 317, 320 L, 320N, 322, 322 FM L, 322 LN, 325, 330, 330 L
311, 311B, 312, 312B, 312B L, 312C, 315, 315B, 315B L, 315C, 317B LN, 318B, 320, 320 L, 320B, 320C, 321B
307, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300, E300B, E450, E650, E70, E70B, EL240B
320N
5I5188
SWITCH AS
311, E110B, E120B, E200B
311, E110B, E120B, E200B
2Q1383
SWITCH AS.
312B, 320 L, 350, 350 L, AP-1000, AP-1050, AP-800
312B, 320 L, 350, 350 L, AP-1000, AP-1050, AP-800
7X6388
SWITCH AS (WIPER)
320, 320 L, 325, 325 LN, 330, 330 L, 350, 375, 375 L, 5080
320, 320 L, 325, 325 LN, 330, 330 L, 350, 375, 375 L, 5080
5I9886
SWITCH AS
307
307
311, 312, 320 L, 325, 325 L, 330 FM L, 330 L
2263156
SWITCH AS
315C, 321C, 321D LCR
315C, 321C, 321D LCR
1275946
SWITCH AS
307, 315
307, 315
5I8065
SWITCH AS
312, 320, 320 L
312, 320, 320 L