1180639 SWITCH AS-ROCKER Caterpillar parts
561N, 572R, 572R II, D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R II, D6R III, D6T, D7R, D7R II, D8R II
Rating:
Alternative (cross code) number:
CA1180639
118-0639
1180639
CA1180639
118-0639
1180639
Weight: 0.30 pounds 0 kg.
Information:
AMPERAGE INDUCTIVE
12
AMPERAGE RESISTIVE
12
NUMBER OF POLES
0
NUMBER OF THROWS
0
TERMINAL SIZE/TYPE
RECEPTACLE
THROW FUNCTION 1
ON
THROW FUNCTION 3
ON
TYPE
ROCKER AS
PIPELAYER, TRACK-TYPE TRACTOR,
This part in 10 request:
Show.
This information for suppliers only!
2024-10-09
2024-09-09
2024-07-23
2024-03-13
2023-09-11
2022-02-07
2022-01-11
2020-04-21
2019-02-08
2019-02-01
Compatible equipment models: 1180639:
Number on catalog scheme:
7
For full view, you need register
Information:
MID 039 CID 1402 FMI 03Conditions Which Generate This Code:
Illustration 1 g01335058
Schematic of the transmission clutch solenoid 2
This diagnostic code is associated with the transmission clutch solenoid 2. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.The possible causes of the diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1402 FMI 03 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J2-51 to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-51 and the circuit that has a low resistance measurement. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE ECM.The disconnect switch and the key start switch remain in the OFF position. The machine harness connectors for the solenoid and the ECM remain disconnected.
At the J2 connector for the ECM, use a wire removal tool to remove wire J839-BR(Brown) from contact J2-51.
Reconnect the machine harness J1 and J2 connectors to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the active diagnostic code. Expected Result:The FMI 03 changes to an FMI 05 after the wire is disconnected.Results:
YES - The FMI 03 changes to a FMI 05 after the wire is disconnected. The ECM has responded correctly to the condition of an open circuit. Reinstall the disconnected wire to the correct space in the ECM connector before proceeding to the next Test Step. Proceed to Test Step 3.
NO - The FMI 03 remains active. The status of the active diagnostic code did not change when the wire was disconnected from the ECM.Repair: The ECM has not responded correctly to the condition of an open circuit. The operation of the ECM is not correct. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacing, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE IS
Illustration 1 g01335058
Schematic of the transmission clutch solenoid 2
This diagnostic code is associated with the transmission clutch solenoid 2. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.The possible causes of the diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1402 FMI 03 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J2-51 to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-51 and the circuit that has a low resistance measurement. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE ECM.The disconnect switch and the key start switch remain in the OFF position. The machine harness connectors for the solenoid and the ECM remain disconnected.
At the J2 connector for the ECM, use a wire removal tool to remove wire J839-BR(Brown) from contact J2-51.
Reconnect the machine harness J1 and J2 connectors to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the active diagnostic code. Expected Result:The FMI 03 changes to an FMI 05 after the wire is disconnected.Results:
YES - The FMI 03 changes to a FMI 05 after the wire is disconnected. The ECM has responded correctly to the condition of an open circuit. Reinstall the disconnected wire to the correct space in the ECM connector before proceeding to the next Test Step. Proceed to Test Step 3.
NO - The FMI 03 remains active. The status of the active diagnostic code did not change when the wire was disconnected from the ECM.Repair: The ECM has not responded correctly to the condition of an open circuit. The operation of the ECM is not correct. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacing, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE IS
Cat SIS web machinery list:
Parts switch Caterpillar catalog:
120M, 12M, 140M, 14M, 160M, 16M, 611, 613C II, 613G, 615C, 784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 844K, 854K, 953D, 96...
613G, 770, 772, 993K, CB-44B, CB-54B, CD-54B, D6R, D6R II, D6R III, D6R STD, D6T, D7R II, D7R XR
561N, 572R, 572R II, 583T, 587T, D10R, D10T, D10T2, D11R, D11T, D5M, D5N, D5R LGP, D6M, D6N, D6R, D6R II, D6R III, D6T, D7R, D7R II, D8R II, D8T, D9T, PL83, PL87
554, 561N, 564, 572R, 572R II, 574B, 583T, 587T, D10R, D10T, D10T2, D11R, D11T, D5M, D5N, D5R LGP, D6M, D6N, D6R, D6R II, D6R III, D6T, D7R, D7R II, D8R II, D8T, D9T, PL83, PL87
572R II, AP-600D, AP-655D, D5N, D6G2 LGP, D6G2 XL, D6N, D6R, D6R II, D6R III, D6R STD, D6T, D7G, D7G2, D7R II, D7R XR, D8R II
120M, 12M, 140M, 14M, 160M, 16M, 24M, 525C, 535C, 545C, 572R II, 587T, 613G, 621G, 623G, 627G, 631G, 637G, 657G, 953D, 963D, 966H, 973D, AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, B...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 24M, 525D, 535D, 545D, 555D, 583T, 587T, 621...
2384C, 2484C, 515, 517, 525, 527, 559C, 561M, 579C, 583R, 587R, 789B, 826C, 836, CB-214D, CB-214E, D10R, D11R, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D6H, D6H XL, D6H XR, D6M, D7H, D8R,...
120H, 120K, 120K 2, 12H, 12K, 130G, 135H, 140H, 140K, 140K 2, 143H, 14H, 160H, 160K, 163H, 16H, 517, 527, 572R, 613C II, 615C, 621B, 627E, 627F, 627G, 637E, 973, 973C, D4H, D4H XL, D4HTSK III, D5H, D5...
525B, 535B, 725, 730, 735, 740, 924G, 924GZ, 953C, 963B, 963C, D5M, D6M, IT28G, R1600, R1600G, R1700 II, R1700G, R2900G, R3000H
24H, 5130, 5130B, 515, 5230B, 525, 525B, 533, 535B, 543, 545, 69D, 769D, 771D, 773D, 775D, 776D, 777D, 785C, 789C, 793C, 844, 854G, 953B, 953C, 963B, 963C, 973, 988F, 988F II, 990, 990 II, 992D, 992G,...
583T, 587T, D10T, D11T, D6R III, D6T, D7R II, D8T, D9T
1194436
SWITCH AS-ROTARY
24H, 834B, 836, 844, 854G, 953C, 963C, 973C, 990 II, 992G, D250E, D250E II, D25D, D300E, D300E II, D350E, D350E II, D400E, D400E II, D40D
24H, 834B, 836, 844, 854G, 953C, 963C, 973C, 990 II, 992G, D250E, D250E II, D25D, D300E, D300E II, D350E, D350E II, D400E, D400E II, D40D
1552719
SWITCH AS-ROCKER
953C, 963C, 973C
953C, 963C, 973C
1236361
SWITCH AS-ROCKER
953C, 963C, 973C
953C, 963C, 973C
1126169
SWITCH AS-ROCKER
950G, 953C, 962G, 963C, 973C, 980G, IT62G
950G, 953C, 962G, 963C, 973C, 980G, IT62G
3E2210
SWITCH AS-ROCKER
953C, 963B, 963C, 973, 973C
953C, 963B, 963C, 973, 973C
561M, 572R, D5M, D6M, D6R, D7R
561N, 572R, 572R II, 583T, 587T, D10R, D10T, D10T2, D11R, D11T, D5M, D5N, D5R LGP, D6M, D6N, D6R, D6R II, D6R III, D6T, D7R, D7R II, D8R II, D8T, D9T, PL83, PL87
D6N, D6R, D6R II, D6R III, D6T, D7R, D7R II, D8R II
613G, 770, 772, 993K, CB-44B, CB-54B, CD-54B, D6R, D6R II, D6R III, D6R STD, D6T, D7R II, D7R XR
1585626
SWITCH AS
950F II, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, D6R II, D6T, D7R, D7R II, D8R II, IT62G, IT62G II
950F II, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, D6R II, D6T, D7R, D7R II, D8R II, IT62G, IT62G II
1913587
SWITCH AS-LIMIT
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6R II, D7R II, D8R II, PL61
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6R II, D7R II, D8R II, PL61
120M, 12M, 140M, 14M, 160M, 16M, 611, 613C II, 613G, 615C, 784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 844K, 854K, 953D, 96...