SWITCH AS-ROCKER 1306584 - Caterpillar

Illustration 34 g02403448
Spin the shaft.
Select the correct spin socket from Table 9 and spin the shaft 20 revolutions in each direction at a maximum of 100 rpm.
Table 10
End play Tolerances
Model Tolerance
(min/max)
D11N
D11R
D11T
D10N
D10R
D10T
D9N
D9R
D9T
D8L
D8N
D8R
D8T
PL83
PL87
578
583R
583T
587R
587T 0.26 to 1.26 mm (0.010 to 0.050 inch)
PL72 0.19 to 1.27 mm (0.007 to 0.050 inch)
1.27 mm (0.05000 inch)
Check the end play.Note: If the end play does not fall within the tolerance given in Table 10, the roller must be disassembled to determine why the tolerance specification is not met.
Illustration 35 g02403449
Lubricate and install stopper.
Lubricate the stopper with a lightweight oil and install in the end of the shaft. The stopper must be installed 7.0 to 15.0 mm (0.28 to 0.59 inch) below the surface of the shaft.
Do not allow air to enter in a surge, and do not use pressure in excess of 138 kPa (20 psi), excess pressure may damage the seals.
Illustration 36 g02902616
170-5664 Test and Fill Cart Gp
Illustration 37 g02902598
FT-2724 Pressure Gauge Tool Gp
Use 170-5664 Test and Fill Cart Gp to evaluate and fill the idler. If 170-5664 Test and Fill Cart Gp is not available. Use FT-2724 Pressure Gauge Tool Gp to perform a pressure test on the idler.Note: Refer to Undercarriage Reconditioning Bulletin, SEBF8594, "Nitrogen Pressure Test Unit" for proper pressure test procedures.
Table 11
Oil Fill Volumes
Model Assembly Oil Volume (ml) Shaft Part Number
D11N
D11R
D11T 1850 50 155-2048
D10N
D10R
D10T 1300 30 154-3306
D9N
D9R
D9T 850 20 104-3494
D8L
D8N
D8R
D8T
PL83
PL87
578
583R
583T
587R
587T 500 15 107-8084
PL72 290 15 471-8577
Add the correct quantity of oil into the roller.Note: Refer to Undercarriage Reconditioning Bulletin, SEBF8574, "Track Roller Oil Fill Volume" for proper fill volumes and oil types. Also refer to Table 11 for oil fill volumes.
Table 12
Plug Depth Specifications
Model Usage Plug Height Above Stopper Surface
D11N
D11R
D11T
D10N
D10R
D10T
D9N
D9R
D9T
D8L
D8N
D8R
D8T
PL83
PL87
PL72
578
583R
583T
587R
587T 0.0 to 5.0 mm (0.00 to 0.20 inch)
Illustration 38 g02403451
Insert plug into stopper.
Use the 5P-7419 Installer Tool to insert the plug into the stopper to proper depth. Refer to Table 12 for proper plug depth specifications.Note: The plug must not be recessed below the stopper surface after assembly.
Illustration 39 g02403452
Tap end of roller shaft to determine if roller contains oil.
Tap the end of the roller shaft to determine if the roller has oil inside. If there is a dull thud, the roller contains oil. If there is a ringing noise, the roller is empty.