1458668 SWITCH AS-PUSH BUTTON Caterpillar parts
950G, 962G, 980G
Rating:
Alternative (cross code) number:
CA1458668
145-8668
1458668
CA1458668
145-8668
1458668
Weight: 0.04 pounds 0 kg.
Information:
AMPERAGE
0
BARREL THREAD SIZE
.62-24
NUMBER OF POSITIONS
2
TERMINAL SIZE/TYPE
CONNECTOR
VOLTAGE
8
V
WHEEL LOADER,
Number on catalog scheme:
1
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 169-5464 Quick Cure Primer
B 155-0695 Thread Lock Compound Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Remove the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Personal injury can result from driveline torque windup under load.Unequal wheel speed can result in driveline torque windup which can cause driveline components to be under load during disassembly.Relieve the driveline torque windup before disassembly.
Illustration 1 g01074389
Support rear drive shaft (1). Remove four bolts (2) and four bolts (3).
Use two people to remove rear drive shaft (1). The weight of the rear drive shaft is approximately 27 kg (60 lb). Installation Procedure
When the rear drive shaft is installed, it must be installed in phase with the rear axle assembly yoke. The rear drive shaft must be installed in phase with the center and front drive shafts. Serious component damage could occur. Be certain that all the joint groups, all the yokes, and all the lubricating fittings are aligned.
Illustration 2 g01074389
Use two people to position rear drive shaft (2) between the output yoke of the output transfer gears and the rear differential. The weight of the rear drive shaft is approximately 27 kg (60 lb).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (2) prior to installation.
Install bolts (2). Tighten bolts (2) to a torque of 160 15 N m (120 11 lb ft).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (3) prior to installation.
Install bolts (3). Tighten bolts (3) to a torque of 160 15 N m (120 11 lb ft). End By:
Install the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 169-5464 Quick Cure Primer
B 155-0695 Thread Lock Compound Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Remove the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Personal injury can result from driveline torque windup under load.Unequal wheel speed can result in driveline torque windup which can cause driveline components to be under load during disassembly.Relieve the driveline torque windup before disassembly.
Illustration 1 g01074389
Support rear drive shaft (1). Remove four bolts (2) and four bolts (3).
Use two people to remove rear drive shaft (1). The weight of the rear drive shaft is approximately 27 kg (60 lb). Installation Procedure
When the rear drive shaft is installed, it must be installed in phase with the rear axle assembly yoke. The rear drive shaft must be installed in phase with the center and front drive shafts. Serious component damage could occur. Be certain that all the joint groups, all the yokes, and all the lubricating fittings are aligned.
Illustration 2 g01074389
Use two people to position rear drive shaft (2) between the output yoke of the output transfer gears and the rear differential. The weight of the rear drive shaft is approximately 27 kg (60 lb).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (2) prior to installation.
Install bolts (2). Tighten bolts (2) to a torque of 160 15 N m (120 11 lb ft).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (3) prior to installation.
Install bolts (3). Tighten bolts (3) to a torque of 160 15 N m (120 11 lb ft). End By:
Install the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar parts catalog:
Parts switch Caterpillar catalog:
1090, 1190, 1190T, 120, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H,...
1090, 1190, 1190T, 120K, 120K 2, 120M, 1290T, 12K, 1390, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 216, 2290, 236, 2390, 2391, 247, 2491, 24H, 24M, 2590, 267, 287, 30/30, 307B, 312B L, 315B L, 317B LN...
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 320B, 320C, 322C, 323D L, 32...
120M, 12M, 140M, 14M, 160M, 16M, 216, 228, 236, 247, 248, 267, 287, 420D, 428D, 430D, 432D, 438D, 442D, 446D, 554, 564, 574, 574B, 65C, 65E, 75C, 75D, 75E, 85C, 85D, 85E, 902, 906, 906H, 906H2, 907H, ...
325C, 330C, 330C L, 345B II, 365B, 365B II, 385B, 533, 543, 65E, 75E, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 825G, 825G II, 825H, 826G II, 826H, 834G, 834H, 836G, 836H, 854G...
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA, 16H NA, 3306B, 3406C, 3406E, 3456, 345B, 345B II, 345B II MH, 345B L, 517, 527, 545, 572R, 583R, 587R, 611, 615C, 62...
120M, 140M, 143H, 160M, 163H NA, 216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 242B, 242B3, 246C, 247B, 247B3, 24H, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 27...
320B, 322B, 322B L, 322C, 322C FM, 325B, 325B L, 330, 3306B, 330B, 330B L, 330C, 330C L, 3406C, 3412C, 345B L, 69D, 824G, 825G, 826G, 918F, 924F, 928F, 938F, 950G, 962G, 980G, AD40, AD45, AE40, AE40 I...
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725C, 730C, 735B, 740B, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, ...
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 814F, 815F, 816F, 824G, 825G, 826G, 918F, 924F, 938F, 950F, 950F II, 950G, 960F, 962G, 966F, 966F II, 966G, 970F, 972G, 980G, IT18F, IT24F, IT28...
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 910G, 914G, 924G, 924GZ, 928G, 930G, 938G, 938G II, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H...
824G, 825G, 826G, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II, 992G, D10R, D11R, FUSION
515, 525, 525B, 535B, 545, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II, 988F II, 990, 990 II, R1300, R1600, R1700G
966F II
1433000
SWITCH AS-TOGGLE
972G II, 980F II, 980G, 988G, 988H, 990 II, 990H, 990K
972G II, 980F II, 980G, 988G, 988H, 990 II, 990H, 990K
966F, D25D, IT28B
6T6168
SWITCH ASSEM.
916, 926, 936
916, 926, 936
3Y6159
SWITCH ASSEM.
920, 966C
920, 966C
1525710
SWITCH AS-PUSH BUTTON
950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II
950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II
1525709
SWITCH AS-PUSH BUTTON
950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II
950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II
1253190
SWITCH AS-ADJUSTABLE
950G, 962G, 966G, 972G, 980G, R2900, R2900G
950G, 962G, 966G, 972G, 980G, R2900, R2900G
3E5520
SWITCH AS-LIMIT
844, 854G, 950G, 962G, 966G, 972G, 980G, 990, 990 II, 992G
844, 854G, 950G, 962G, 966G, 972G, 980G, 990, 990 II, 992G
824G, 824G II, 824H, 834G, 834H, 844H, 854G, 854K, 950G, 962G, 966G, 972G, 980G, 988G, 988H, 990 II, 990H, 992G, 992K, 993K, 994, 994D, 994F, R1300, R1300G, R1300G II, R1600, R1600G, R1600H, R1700G, R...
1458669
SWITCH AS-PUSH BUTTON
950G, 962G, 980G
950G, 962G, 980G