1636719 SWITCH AS-ROCKER Caterpillar parts
312C L, 315C, 318C, 320C, 320C FM, 320C L, 322C, 325C, 325C FM, 330C FM, 330C L, 330C MH, 345C
Rating:
Alternative (cross code) number:
CA1636719
163-6719
1636719
CA1636719
163-6719
1636719
Weight: 0.07 pounds 0 kg.
Information:
AMPERAGE INDUCTIVE
3
AMPERAGE RESISTIVE
5
NUMBER OF POLES
1
NUMBER OF THROWS
1
TERMINAL SIZE/TYPE
CONNECTOR
THROW FUNCTION 1
OFF
THROW FUNCTION 2
ON-MOMENTARY
TYPE
ROCKER AS
FUNCTIONALITY
WSHLD WASHER
EXCAVATOR, SHOVEL LOGGER,
Compatible equipment models: 1636719:
Number on catalog scheme:
1
For full view, you need register
Information:
start by:a) remove drive sprockets 1. Drain the oil from the final drive housing. Remove cover (1). Put wedges between the final drive gear and housing to keep the final drive gear in position.2. Remove cap (3) and loosen the bolts on the side not to be removed.3. Lift the frame and install blocks so the opposite half of the cap will clear the axle housing.4. Install tool (A) under the opposite tandem housing.5. Fasten a hoist to the axle housing. Remove nuts (2) that hold the axle housing to the final drive housing.6. Install two 1/2"-13 NC forcing screws to remove the axle housing from the final drive housing. Pull the axle housing off of the studs, axle out of the splines in the hub and lower the assembly to be clear of the frame. Remove the axle housing and axle. The weight is 350 lb. (158 kg). 7. Remove seal and shims (4). Keep the shims with the axle housing for correct installation.Install Axle Housings And Axles
1. Install the original amount of shims (1) and the O-ring seal on axle housing (2). If a new hub or support bearing is installed, make the adjustment of the support bearings as given in Step 2.2. Make the adjustment of the support bearing in the following way: a) Put the axle housing on the housing for the final drive.b) Install the nuts that fasten the housings together. Turn the gear to put the bearings in their seat.c) Check the end clearance of the final drive gear with tooling (A).d) Use a thickness gauge to find the amount of shims needed between the axle housing and the housing for the final drive.e) Use shims as needed to get .003 to .011 in. (0.08 to 0.28 mm) end clearance. Install a minimum of two shims on each side. 3. Install cap (3), bolts and locks. Tighten the bolts on the other side. 4. Install final drive cover (4). Fill the final drive with lubrication to the correct level. See LUBRICATION AND MAINTENANCE GUIDE.end by:a) install drive sprocketsDisassemble Axle Housings And Axles
start by:a) remove axle housings and axles1. Remove O-ring seals and shims from axle housing. 2. Remove bolts (2) and pivot bearing cage (1). 3. Remove thrust washers (6). Remove bearings (5) from the pivot bearing cage. Remove bolts (4) and the locks from bearing adjuster (3). 4. Remove bearing adjuster (3) from plate (7) with tooling (A). Remove the shims between the end of the axle housing and bearing adjuster.5. Fasten a hoist and remove the axle from the axle housing. The weight is 110 lb. (49.5 kg).6. Remove the bearing cones from the axle with tooling (B). 7. Remove the bearing cups from the axle housing with tooling (C). Remove the axle oil seal from the housing.8. Remove the O-ring seals and gasket from the housing, cage and plate.Assemble Axle Housings And Axles
1. Install the oil seal in the housing with the lip of the seal toward the final
1. Install the original amount of shims (1) and the O-ring seal on axle housing (2). If a new hub or support bearing is installed, make the adjustment of the support bearings as given in Step 2.2. Make the adjustment of the support bearing in the following way: a) Put the axle housing on the housing for the final drive.b) Install the nuts that fasten the housings together. Turn the gear to put the bearings in their seat.c) Check the end clearance of the final drive gear with tooling (A).d) Use a thickness gauge to find the amount of shims needed between the axle housing and the housing for the final drive.e) Use shims as needed to get .003 to .011 in. (0.08 to 0.28 mm) end clearance. Install a minimum of two shims on each side. 3. Install cap (3), bolts and locks. Tighten the bolts on the other side. 4. Install final drive cover (4). Fill the final drive with lubrication to the correct level. See LUBRICATION AND MAINTENANCE GUIDE.end by:a) install drive sprocketsDisassemble Axle Housings And Axles
start by:a) remove axle housings and axles1. Remove O-ring seals and shims from axle housing. 2. Remove bolts (2) and pivot bearing cage (1). 3. Remove thrust washers (6). Remove bearings (5) from the pivot bearing cage. Remove bolts (4) and the locks from bearing adjuster (3). 4. Remove bearing adjuster (3) from plate (7) with tooling (A). Remove the shims between the end of the axle housing and bearing adjuster.5. Fasten a hoist and remove the axle from the axle housing. The weight is 110 lb. (49.5 kg).6. Remove the bearing cones from the axle with tooling (B). 7. Remove the bearing cups from the axle housing with tooling (C). Remove the axle oil seal from the housing.8. Remove the O-ring seals and gasket from the housing, cage and plate.Assemble Axle Housings And Axles
1. Install the oil seal in the housing with the lip of the seal toward the final
Cat SIS web machinery list:
Parts switch Caterpillar catalog:
1090, 1190, 1190T, 120M 2, 1290T, 1390, 2290, 2384C, 2390, 2391, 2484C, 2491, 2590, 2864C, 311D LRR, 3126B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313...
311C, 312, 312C, 312C L, 314C, 318B, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311, 311B, 312, 312B, 312B L, 312C, 315, 315B, 315B L, 315C, 317B LN, 318B, 320, 320 L, 320B, 320C, 321B
115, 303, 307B, 307C, 308C, 311B, 312B, 312B L, 313B, 315B, 315B FM L, 315B L, 317B LN, 318B, 320B, 320B FM LL, 320B L, 320B U, 322B, 322B L, 322B LN, 325B, 325B L, 330B, 330B L, 345B, 345B II, 345B I...
311C, 312C, 312C L, 312D, 314C, 315C, 315D L, 318C, 319C, 319D, 320C, 320C FM, 320C L, 320D, 320D L, 320D LRR, 321C, 321D LCR, 322C, 322C FM, 323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 325C, 325...
311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 313D, 313D2, 314C, 314D CR, 314D LCR, 315C, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L,...
311C, 311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 315C, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN
311C, 312C, 314C, 315C, 318C, 319C, 320C, 320C FM, 321C, 322C, 322C FM, 325C, 325C FM, 325C L, 330C, 330C FM, 330C L, 330C MH, 345C, 345C MH, 365C, 365C L, 365C L MH, 385C, 385C FS, 385C L, 385C L MH,...
319D, 319D L, 319D LN, 320C, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 330C, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D L, 336D LN, 345C, 345C L, 34...
307C, 311C, 320C
2018793
SWITCH AS-ROCKER
307C, 312C, 315C, 318C, 319C
307C, 312C, 315C, 318C, 319C
120G, 12G, 130G, 140G, 16G, 307C, 307D, 308C, 308D, 311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D2 L...
1648232
SWITCH AS-DIAL
307C, 307D
307C, 307D
1673629
SWITCH AS-ROCKER
307C, 311C
307C, 311C
311C, 312C, 312C L, 314C, 315C
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2 L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, ...
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2 L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, ...
312C, 312C L, 315C, 318C, 319C, 320C, 322C, 325C, 330C L
312C, 312C L, 315C, 318C, 320C, 322C, 325C, 330C L, SAT223, SAT22DB, SAT318, SAT318T, SAT322
1636718
SWITCH AS-ROCKER
312C L, 315C, 318C, 320C, 320C FM, 320C L, 322C, 325C, 325C FM, 330C FM, 330C L, 330C MH, 345C
312C L, 315C, 318C, 320C, 320C FM, 320C L, 322C, 325C, 325C FM, 330C FM, 330C L, 330C MH, 345C