1753245 SWITCH AS-PRESSURE Caterpillar parts
814F, 815F, 816F, 834B, 836, 994, 994D, AD40, AE40, R2900
Rating:
Alternative (cross code) number:
CA1753245
175-3245
1753245
CA1753245
175-3245
1753245
Weight: 0.43 pounds 0 kg.
Information:
ACTUATION PRESSURE
8270 KPA
kPa
CONNECTOR TYPE
3-SS
DEACTUATION PRESSURE
6890 KPA
kPa
THREAD SIZE
.56-18
AMP.[RESISTIVE]
1.5A
CONTACT PRESSURE-MAX.
20700 KPA
CONATCT POSITION
NC-NO
OPEN CYCLE LIFE
100000
SENSED MEDIA
OIL-FUEL-AIR
SUPPLY VOLTAGE
28V
LANDFILL COMPACTOR, WHEEL LOADER,
Compatible equipment models: 1753245:
Number on catalog scheme:
61
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1858 Retaining Ring Pliers 1
B 1P-1854 Retaining Ring Pliers 1
C 134-2837 Piston Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00523650
Inspect the condition of the bores in the compression brake housing. The bores must be free of wear and score marks.
Illustration 2 g00524784
Illustration 3 g00524783
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Inspect the condition of master piston (21). The master piston must be free of wear and score marks. Replace master piston (21), if necessary.
Install master piston (21) in the bore. Install the small end of spring (20) in the bore. Install retaining washer (19), and retaining ring (18) over master piston (21) and compress until retaining washer (19) is below the retaining ring groove. Install retaining ring (18) with Tooling (B). Ensure that retaining ring (18) is fully seated in the groove.Note: Repeat Steps 2 and 3 for the remaining master piston.
Illustration 4 g00524782
Illustration 5 g00523486
Illustration 6 g00524785
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Inspect the condition of slave piston (17). The slave piston must be free of wear and score marks. Replace slave piston (17), if necessary.
Install slave piston (17), springs (16), spring retainer (14), and retaining ring (15) in the bore.
Place Tooling (C) over slave piston adjustment screw (13) and spring retainer (14). Turn the handle on Tooling (C) until spring retainer (14) is approximately 1.0 mm (0.04 inch) below the retaining ring groove. Install retaining ring (15) with Tooling (A) .
Remove Tooling (C) slowly in order to ensure that retaining ring (15) is properly seated in the groove.Note: Repeat Steps 4 through 7 for the remaining slave piston.
Illustration 7 g00523484
Screw in slave piston adjustment screw (13) until contact is made with the slave piston.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1858 Retaining Ring Pliers 1
B 1P-1854 Retaining Ring Pliers 1
C 134-2837 Piston Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00523650
Inspect the condition of the bores in the compression brake housing. The bores must be free of wear and score marks.
Illustration 2 g00524784
Illustration 3 g00524783
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Inspect the condition of master piston (21). The master piston must be free of wear and score marks. Replace master piston (21), if necessary.
Install master piston (21) in the bore. Install the small end of spring (20) in the bore. Install retaining washer (19), and retaining ring (18) over master piston (21) and compress until retaining washer (19) is below the retaining ring groove. Install retaining ring (18) with Tooling (B). Ensure that retaining ring (18) is fully seated in the groove.Note: Repeat Steps 2 and 3 for the remaining master piston.
Illustration 4 g00524782
Illustration 5 g00523486
Illustration 6 g00524785
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Inspect the condition of slave piston (17). The slave piston must be free of wear and score marks. Replace slave piston (17), if necessary.
Install slave piston (17), springs (16), spring retainer (14), and retaining ring (15) in the bore.
Place Tooling (C) over slave piston adjustment screw (13) and spring retainer (14). Turn the handle on Tooling (C) until spring retainer (14) is approximately 1.0 mm (0.04 inch) below the retaining ring groove. Install retaining ring (15) with Tooling (A) .
Remove Tooling (C) slowly in order to ensure that retaining ring (15) is properly seated in the groove.Note: Repeat Steps 4 through 7 for the remaining slave piston.
Illustration 7 g00523484
Screw in slave piston adjustment screw (13) until contact is made with the slave piston.
Caterpillar parts catalog:
Parts switch Caterpillar catalog:
320B, 322B, 322B L, 322C, 322C FM, 325B, 325B L, 330, 3306B, 330B, 330B L, 330C, 330C L, 3406C, 3412C, 345B L, 69D, 824G, 825G, 826G, 918F, 924F, 928F, 938F, 950G, 962G, 980G, AD40, AD45, AE40, AE40 I...
725, 730, 735, 740, AD40, AD45, AE40, AE40 II, C9, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX31-P600, CX35-C18I, R1700G, TH31-E61, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I, TH35-C15T, TH35-E81
508, 613C, 7155, 814B, 815B, 824C, 826C, 834B, 836, 950B, 950F, 966D, 966F, 980C, 980F, 988B, 992C, 994, D6H, D6H II, D6H XL, D6H XR, D7H, D8N, D8R, D9R
120G, 12G, 12H ES, 12H NA, 130G, 140G, 140H ES, 140H NA, 143H, 14G, 160G, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 578, 589, 613C, 615C, 621E, 621F, 623E, 627E, 627F, 631E, 637E, 651E, 657E, 768C, 769C...
3516B, 5130B, 5230, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785C, 785D, 789, 789C, 789D, 793C, 793D, 797, 797B, 994D, 994F, 994H, D11N, D11R
120G, 12G, 12H ES, 12H NA, 130G, 140G, 140H ES, 140H NA, 143H, 14G, 160G, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 245D, 578, 589, 611, 613C, 615, 615C, 621E, 621F, 623E, 627E, 627F, 631E, 637E, 651E, ...
589, 611, 613C II, 615C, 627E, 631E, 633E II, 637E, 651E, 657E, 826C, 834B, 836, 980C
2384C, 2484C, 515, 517, 525, 527, 559C, 561M, 579C, 583R, 587R, 789B, 826C, 836, CB-214D, CB-214E, D10R, D11R, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D6H, D6H XL, D6H XR, D6M, D7H, D8R,...
140G, 517, 527, 561M, 631E, 633E II, 637E, 735, 735B, 740, 740B, 777C, 777D, 824C, 918F, 924F, 928F, 950F II, 953B, 963B, 980C, CB-634, CB-634C, CS-531C, CS-531D, CS-533C, CS-533D, CS-563C, CS-563D, C...
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725C, 730C, 735B, 740B, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, ...
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 814F, 815F, 816F, 824G, 825G, 826G, 918F, 924F, 938F, 950F, 950F II, 950G, 960F, 962G, 966F, 966F II, 966G, 970F, 972G, 980G, IT18F, IT24F, IT28...
320 L, 910E, 918F, 924F, 928F, 936F, 938F, 950F, 950F II, 960F, 966F II, 970F, 980F, 980F II, 994, 994D, IT12B, IT18F, IT24F, IT28F, IT38F
3E9342
SWITCH AS-LIQUID LEVEL
5130, 5230, 789B, 950F, 950F II, 960F, 966F, 966F II, 970F, 980F, 994, 994D
5130, 5230, 789B, 950F, 950F II, 960F, 966F, 966F II, 970F, 980F, 994, 994D
8N1425
SWITCH
776C, 777, 777B, 784B, 785, 785B, 789, 789B, 793B, 994
776C, 777, 777B, 784B, 785, 785B, 789, 789B, 793B, 994
776, 776C, 777, 777B, 784B, 785, 785B, 789, 789B, 793, 793B, 994, R1700 II
1167151
SWITCH AS
784B, 785B, 789B, 793B, 994
784B, 785B, 789B, 793B, 994
6T4044
SWITCH GP
980C, D25D, D40D
980C, D25D, D40D
365B, 365B II, 365C, 365C L, 374D L, 385B, 385C, 385C L, 390D, 390D L, 5090B, 5230B, 844, 844H, 854K, 988F, 988F II, 990, 990 II, 990H, 992D, 992K, 993K, 994H
322B L, 325B, 325B L, 330B L, 345B, 345B II, 345B L, 365B L, 385B, 385C, 385C L, 5130, 5130B, 5230, 854G, 988F, 992D, 992G, 993K, 994F
3E6452
SWITCH AS-PRESSURE
322B L, 325B L, 330B L, 824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, 988F, 992D
322B L, 325B L, 330B L, 824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, 988F, 992D
4E8950
SWITCH AS-PRESSURE
988F, 988F II, 992D
988F, 988F II, 992D
7T8530
SWITCH AS-LIQUID LEVEL
950F, 966F, 980F
950F, 966F, 980F
5110B, 5130B, 5230, 5230B, 797, 797B, 797F, 990K, 994, 994D