2495483 SWITCH AS-ROCKER Caterpillar parts
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24M, 336D L, 972K, 980K
Rating:
Alternative (cross code) number:
CA2495483
249-5483
2495483
CA2495483
249-5483
2495483
Weight: 0.01 pounds 0 kg.
Information:
AMPERAGE INDUCTIVE
12
AMPERAGE RESISTIVE
12
FUNCTIONALITY
ILLUMINATED
NUMBER OF POLES
0
NUMBER OF THROWS
0
TERMINAL SIZE/TYPE
BLADE
THROW FUNCTION 1
ON MOMENTARY
THROW FUNCTION 3
ON MOMENTARY
TYPE
ROCKER
THROW FUNCTION 2
ON
MOBILE HYD POWER UNIT, WHEEL LOADER,
Compatible equipment models: 2495483:
Number on catalog scheme:
1
For full view, you need register
Information:
Carrier Bore Preparation
Inspect the joint faces of the carrier bearing cap for wear or damage. Machine the faces flat if necessary.
Install the bearing caps and tighten to the torque specification listed in the applicable Disassembly and Assembly manual.
Clamp the carrier on the table of a precision boring machine. Find the centerlines of diameter (A) and the bearing bore opposite the one being repaired, to establish the centerline of the new bearing bore.Note: If the bore being repaired still has some surface that is not worn, use that surface and the opposite bore to establish the center-line of the new bearing bore, instead of using diameter A.
Machine the damaged bore to the dimensions shown in Illustration 5 and Table 4. After machining, the new bearing must be in alignment with the opposite bore within 0.15 mm (0.006 inch).Cap Preparation
Remove the bearing cap.
Drill and ream a 7.76 mm (0.305 inch) diameter hole in the cap as shown in Illustration 6
Press a 6F-0698 Dowel into the hole. The dowel must extend 4.5 mm (0.18inch) above the surface of the cap.
Illustration 6 g02317022Cap Modifications (8) Dimension F (9) 7.755 0.013 mm (0.3053 0.0005 inch) Diameter 5.0 mm (0.20nch) Deep.Preliminary Cage Preparation (992C Only)
Note: The following is an optional method for preliminary cage preparation.
Clamp a 5T-5966 Bearing Cage on the outside diameter in a lathe. Do not overtighten the jaws.
Machine the cage bore for the bearing and cut the threads for the retaining nut. Refer to Illustration 7 for the dimensions
Drill a 9.20 mm (0.362 inch) diameter hole, as shown in Illustration 7.
Illustration 7 g02317041
Modifications to 5T-5966 Bearing Cage. Refer to Table 2 for Dimensions.
(10) 240.72 0.13 mm (9.477 0.005 inch) Diameter. 28.3 mm (1.11 inch) Deep.9.562 inch - 12 THD 25.3 mm (0.996 inch) Deep.Thread pitch range : 241.696 mm (9.516 inch) to 241.510 mm (9.508 inch) (11) 1.5 0.5 mm x 45° (0.06 0.02 x 45°) (12) 1.5 0.5 mm (0.06 0.02 inch) (13) 240.000 0.040 mm (9.4488 0.0016 inch) Diameter. (Concentric with the outside diameter within 0.50 mm) (0.02 inch) (14) 9.2 mm (0.362 inch) Drill. 4.0 mm (0.16 inch) Deep.Final Machining and Assembly
If necessary, trim the bearing cage flush with the side of the carrier bore.
Machine a slot in the new cage for the nut lock tab. Use the bearing cap as a template.
Assemble the differential carrier using standard Service Manual procedures, except as noted in Step 4 (992C)
Clean the outside diameter of the bearing cup and inside diameter of the cage with Quick Cure Primer. Apply a thin coat of Bearing Mount to the outside diameter of the cup before final assembly. Be sure that necessary adjustments are made immediately after assembly.
Inspect the joint faces of the carrier bearing cap for wear or damage. Machine the faces flat if necessary.
Install the bearing caps and tighten to the torque specification listed in the applicable Disassembly and Assembly manual.
Clamp the carrier on the table of a precision boring machine. Find the centerlines of diameter (A) and the bearing bore opposite the one being repaired, to establish the centerline of the new bearing bore.Note: If the bore being repaired still has some surface that is not worn, use that surface and the opposite bore to establish the center-line of the new bearing bore, instead of using diameter A.
Machine the damaged bore to the dimensions shown in Illustration 5 and Table 4. After machining, the new bearing must be in alignment with the opposite bore within 0.15 mm (0.006 inch).Cap Preparation
Remove the bearing cap.
Drill and ream a 7.76 mm (0.305 inch) diameter hole in the cap as shown in Illustration 6
Press a 6F-0698 Dowel into the hole. The dowel must extend 4.5 mm (0.18inch) above the surface of the cap.
Illustration 6 g02317022Cap Modifications (8) Dimension F (9) 7.755 0.013 mm (0.3053 0.0005 inch) Diameter 5.0 mm (0.20nch) Deep.Preliminary Cage Preparation (992C Only)
Note: The following is an optional method for preliminary cage preparation.
Clamp a 5T-5966 Bearing Cage on the outside diameter in a lathe. Do not overtighten the jaws.
Machine the cage bore for the bearing and cut the threads for the retaining nut. Refer to Illustration 7 for the dimensions
Drill a 9.20 mm (0.362 inch) diameter hole, as shown in Illustration 7.
Illustration 7 g02317041
Modifications to 5T-5966 Bearing Cage. Refer to Table 2 for Dimensions.
(10) 240.72 0.13 mm (9.477 0.005 inch) Diameter. 28.3 mm (1.11 inch) Deep.9.562 inch - 12 THD 25.3 mm (0.996 inch) Deep.Thread pitch range : 241.696 mm (9.516 inch) to 241.510 mm (9.508 inch) (11) 1.5 0.5 mm x 45° (0.06 0.02 x 45°) (12) 1.5 0.5 mm (0.06 0.02 inch) (13) 240.000 0.040 mm (9.4488 0.0016 inch) Diameter. (Concentric with the outside diameter within 0.50 mm) (0.02 inch) (14) 9.2 mm (0.362 inch) Drill. 4.0 mm (0.16 inch) Deep.Final Machining and Assembly
If necessary, trim the bearing cage flush with the side of the carrier bore.
Machine a slot in the new cage for the nut lock tab. Use the bearing cap as a template.
Assemble the differential carrier using standard Service Manual procedures, except as noted in Step 4 (992C)
Clean the outside diameter of the bearing cup and inside diameter of the cage with Quick Cure Primer. Apply a thin coat of Bearing Mount to the outside diameter of the cup before final assembly. Be sure that necessary adjustments are made immediately after assembly.
Cat SIS web machinery list:
Parts switch Caterpillar catalog:
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 236D, 242D, 246C, 246D, 24M, 256C, 257D...
120M, 140M, 143H, 160M, 163H NA, 216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 242B, 242B3, 246C, 247B, 247B3, 24H, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 27...
236D, 242D, 257D, 259D, 272D, 272D XHP, 299D, 299D XHP, 3126B, 3512C, 3516B, 621G, 623G, 627G, 631G, 637G, 657G, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 938H, 95...
1090, 1190, 1190T, 120M 2, 1290T, 1390, 2290, 2384C, 2390, 2391, 2484C, 2491, 2590, 2864C, 311D LRR, 3126B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313...
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2 L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, ...
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2 L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, ...
311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 313D, 313D2, 314C, 314D CR, 314D LCR, 315C, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L,...
120M, 12M, 140M, 14M, 160M, 16M, 611, 613C II, 613G, 615C, 784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 844K, 854K, 953D, 96...
120M, 12M, 140M, 14M, 160M, 16M, 24M, 525C, 535C, 545C, 572R II, 587T, 613G, 621G, 623G, 627G, 631G, 637G, 657G, 953D, 963D, 966H, 973D, AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, B...
120M, 12M, 140M, 14M, 160M, 16M, 24M, 950G II, 950H, 953D, 962G II, 962H, 963D, 966G II, 966H, 972G II, 972H, 973D, 980H, D6K, D6K LGP, D6N LGP, D7E, IT62H, PL61
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 24M, 525D, 535D, 545D, 555D, 583T, 587T, 621...
120M, 120M 2, 12M, 12M 2, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 24M, 613G, 953D, 963D, 973D, D3K XL, D4K XL, D5K LGP, D6K, D6K LGP, D6K XL, D7E, PL61
2509279
SWITCH AS-ROCKER
992K, 994F
992K, 994F
785C, 789C, 793C, 797, 797B, 854K, 992K
2238975
SWITCH AS-ROCKER
814F II, 815F II, 816F II, 824H, 825H, 826H, 834H, 836H, 844H, 854G, 854K, 988H, 990H, 992G, 992K, 994F
814F II, 815F II, 816F II, 824H, 825H, 826H, 834H, 836H, 844H, 854G, 854K, 988H, 990H, 992G, 992K, 994F
3E8763
SWITCH AS
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 725, 7...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 725, 7...
3E9319
SWITCH AS-ROCKER
120H NA, 120K, 120K 2, 12H NA, 12K, 135H, 140H NA, 140K, 140K 2, 160H NA, 160K, 980G II, 980H
120H NA, 120K, 120K 2, 12H NA, 12K, 135H, 140H NA, 140K, 140K 2, 160H NA, 160K, 980G II, 980H
834B, 988B, 992C, D8L, D9L
992C, D10N, D11N, D8L, D9L, D9N
785, 789, 834B, 836, 950F, 950F II, 960F, 966F, 966F II, 970F, 988B, 992C, 994, R1700 II, RR-250, SS-250
7V3604
SWITCH AS
980C, 988B, 992C
980C, 988B, 992C
4244908
SWITCH AS-ROCKER
972K, 980K
972K, 980K
3684538
SWITCH AS-ROCKER
972K, 980K, 988K
972K, 980K, 988K