3303021 SWITCH GP-PRESSURE Caterpillar parts
C1.5
Rating:
Alternative (cross code) number:
CA3303021
330-3021
3303021
CA3303021
330-3021
3303021
INDUSTRIAL ENGINE,
Compatible equipment models: 3303021:
Number on catalog scheme:
For full view, you need register
Information:
Illustration 1 g01377117
Schematic of the right front drive pump reverse control solenoidThis diagnostic code is associated with the right front drive pump reverse control solenoid (all wheel drive). The FMI 13 diagnostic code is activated when the Implement ECM detects the right front drive pump reverse solenoid that needs calibration. Once the calibration for the right front drive pump reverse control solenoid has been performed successfully, this diagnostic code will disappear. This failure is active on a new ECM.Possible causes of this diagnostic code are listed below:
The ECM has been replaced or new software has been installed.
The ECM has failed.System Response:The machine response is listed below:
AWD will not operate.Note: Ensure that you have repaired any condition that would cause other active diagnostic codes that are related to this solenoid. If the other diagnostic codes are active, troubleshoot those codes first. Then perform this procedure.Note: Ensure that the diagnostic code of CID 2298 FMI 13 is active before performing this procedure.Test Step 1. CHECK THE CALIBRATION
Perform the calibration procedure. Refer to the Testing and Adjusting Section of the Service Manual for the correct procedure.
Observe the status of the CID 2298 FMI 13.Expected Result:The CID 2298 FMI 13 is active.Results:
OK - The CID 2298 FMI 13 is active. The diagnostic code has not been corrected. Verify that the correct software has been flashed into the ECM, or that the correct ECM is installed on the machine. Then repeat the calibration.Repair: If the diagnostic code is still active and the cause of the diagnostic code is not found replace the ECM. It is unlikely that the ECM has failed. Verify that the solenoid and associated circuits are correct before you replace the ECM.STOP
NOT OK - The CID 2298 FMI 13 is not active. The calibration corrected the condition that caused the diagnostic code. Repair: Resume normal operation.STOP
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts switch Caterpillar catalog:
3111130
SWITCH GP-TEMPERATURE
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34
3111129
SWITCH GP-PRESSURE
C1.5, CB-22
C1.5, CB-22
3082314
SWITCH GP-START
C0.5, C0.7, C1.1, C1.5, C1.6, C2.2
C0.5, C0.7, C1.1, C1.5, C1.6, C2.2
3156638
SWITCH GP-PRESSURE
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3157819
SWITCH GP-PRESSURE
216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3024C, AP-255E, BB-621C, C1.5, C2.2, CB-34, CB34B, CB34B XW, CC34B
216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3024C, AP-255E, BB-621C, C1.5, C2.2, CB-34, CB34B, CB34B XW, CC34B
4523668
SWITCH
C0.5, C1.5, C1.6, C2.2, CB-22
C0.5, C1.5, C1.6, C2.2, CB-22
3713767
SWITCH GP-TOGGLE
3512, 3512B, 3512C, C27, C32
3512, 3512B, 3512C, C27, C32
3054023
SWITCH-NETWORK
Caterpillar
Caterpillar
3354439
SWITCH GP-SHUTDOWN
Caterpillar
Caterpillar
3508400
SWITCH GP-ROCKER
312E L, 316E L, 318E L, 320E L, 320E LRR, 324E L, 329E L, 336E LH, 336E LN, 349E L, 349E L VG, 349F L
312E L, 316E L, 318E L, 320E L, 320E LRR, 324E L, 329E L, 336E LH, 336E LN, 349E L, 349E L VG, 349F L
3560205
SWITCH GP-DISCONNECT
C15, C15 I6, C18 I6
C15, C15 I6, C18 I6
2446002
SWITCH GP-MAGNETIC
3508C, 3512C
3508C, 3512C