AVSPARE.COM
parts catalog

SWITCH AS-PUSH BUTTON 4416544 - Caterpillar



4416544 SWITCH AS-PUSH BUTTON Caterpillar parts SWITCH
Rating:
11
Alternative (cross code) number:
CA4416544
441-6544
4416544
Caterpillar 4416544 SWITCH AS-PUSH BUTTON
Weight: 0.22 pounds 0 kg.

Buy SWITCH AS-PUSH BUTTON 4416544 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 67
 
  For full view, you need register

Information:

Introduction
When replacing the 8N2501 Governor Housing Assembly in the 3300 Family Of Engines with Scroll Fuel Systems, it is possible to have an interference between components within the governor or the rack may not move all the way to the "Fuel Off" position. These conditions may exist because of casting shifts during the manufacturing process of the governor housing.To ensure that the governor will function properly, it is necessary to check the assembled dimension for rack lever travel and possibly replace the original 8N3087 Stop and 2W9305 Plate. Follow the procedure in this instruction to perform this check.Reference: Service Manual, Parts Book.Recommended Additional Parts
Installation
1. Assemble the components of the governor group using a new 8N2501 Governor Housing Assembly and the original 8N3087 Stop and 2W9305 Plate. Refer to the Service Manual for the assembly procedure.
Dimension (A).2. Measure the distance between the face of the governor housing assembly and the rack lever dimension (A). This dimension should be 18.6 1.0 mm (0.73 .04 in).3. If dimension (A) is within the specified limit of 17.6 to 19.6 mm (0.69 to 0.77 in), install the governor assembly.* If dimension (A) measured in Step 2, is greater than 19.6 mm (0.77 in), proceed to Step 4.* If dimension (A) measured in Step 2, is less than 17.6 mm (0.69 in), proceed to Step 5.
(1) 8N3087 Stop. (2) 2W9305 Plate. (3) Grind location.4. Remove 2W9305 Plate (2) and grind some material from the plate at area (3) shown shaded in above illustration. Re-install plate (2) and check for correct dimension (A).Install the governor assembly when the correct dimension (A) has been achieved.5. Remove the original 8N3087 Stop (1) and 2W9305 Plate (2), and replace with new parts.Check dimension (A) per Step 2 above. Install the governor assembly when the correct dimension (A) has been achieved.

Caterpillar parts catalog:

Caterpillar parts catalog
PL83 PIPELAYER CB200001-UP (MACHINE) POWERED BY C15 Engine
PL83 PIPELAYER DLW00001-UP (MACHINE) POWERED BY C15 Engine
PL87 PIPELAYER ZAC00001-UP (MACHINE) POWERED BY C15 Engine
PL72 PIPELAYER P7200001-UP (MACHINE) POWERED BY C9 Engine
PL72 PIPELAYER P7300001-UP (MACHINE) POWERED BY C9 Engine
PL61 Pipelayer FNZ00001-UP (MACHINE)
PL61 Pipelayer 6P200001-UP (MACHINE)


Parts switch Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.