5L5500 SWITCH (Fuel Pressure) Caterpillar parts
120G, 130G, 3304, 3306, 627B, 637B, 637D, 657B, 666, 769C, 773B, 777, AP-200, CB-314, D342C, D343, D348, D353C, D398, RR-250
Rating:
Alternative (cross code) number:
CA5L5500
5L-5500
5L5500
CA5L5500
5L-5500
5L5500
Weight: 0.20 pounds 0 kg.
ASPHALT PAVER, WHEEL SCRAPER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$62.61
30 Dec 2023
US: Florida-Parts-Z
5L5500 - Switch (Hour Meter & Oil Pressure) 3N7081 fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$62.61
18 Feb 2022
US: Florida-Parts-Z
5L5500 - Switch (Hour Meter & Oil Pressure) 3N7081 fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$37.26
04 May 2022
Amazon.com
CTP 5L5500 Electrical Contactor
CTP Sold as each || Highly Efficient || Easy in-and-out fit
CTP Sold as each || Highly Efficient || Easy in-and-out fit
Number on catalog scheme:
9
For full view, you need register
Compatible equipment models: 5L5500:
Information:
Removal Procedure
Start By:
Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Remove the housing for the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00541252
Remove two socket head bolts (1) that hold bridge (2) in position.
Remove bridge (2) from the cylinder block.
Illustration 2 g00541253
Note: Inspect the main bearing caps and the connecting rod caps for the proper identification marks. The identification marks should give the location and the direction of the bearings in the engine.
Remove ten main bearing cap bolts (3) from the main bearing caps.
Remove five main bearing caps (4) from the cylinder block.
Remove the lower main bearings and the lower thrust washers. Keep the lower main bearings with the respective main bearing caps.
Illustration 3 g00541254
Note: The connecting rod caps can be held on the connecting rod with two bolts and two nuts. The connecting rod caps can also be held on the connecting rod with two bolts that are threaded into the connecting rod.
Remove eight nuts (5) from the connecting rod caps.
Remove four connecting rod caps (6) from the connecting rods.
Remove the bearings from connecting rod caps (6). Keep the connecting rod bearings with the respective connecting rod cap.
Do not allow the connecting rods to strike the piston cooling jets. Damage or misalignment may occur.
Push the piston assemblies into the cylinder bores.
Illustration 4 g00541256
Attach lifting straps and a suitable lifting device to crankshaft (7) .
Lift crankshaft (7) out of the cylinder block. The weight of the crankshaft is 29 kg (65 lb). Do not scratch any of the finished surfaces on the crankshaft.
Illustration 5 g00541257
Remove upper main bearings (8) and upper thrust washers (9) from the cylinder block.
Start By:
Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Remove the housing for the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00541252
Remove two socket head bolts (1) that hold bridge (2) in position.
Remove bridge (2) from the cylinder block.
Illustration 2 g00541253
Note: Inspect the main bearing caps and the connecting rod caps for the proper identification marks. The identification marks should give the location and the direction of the bearings in the engine.
Remove ten main bearing cap bolts (3) from the main bearing caps.
Remove five main bearing caps (4) from the cylinder block.
Remove the lower main bearings and the lower thrust washers. Keep the lower main bearings with the respective main bearing caps.
Illustration 3 g00541254
Note: The connecting rod caps can be held on the connecting rod with two bolts and two nuts. The connecting rod caps can also be held on the connecting rod with two bolts that are threaded into the connecting rod.
Remove eight nuts (5) from the connecting rod caps.
Remove four connecting rod caps (6) from the connecting rods.
Remove the bearings from connecting rod caps (6). Keep the connecting rod bearings with the respective connecting rod cap.
Do not allow the connecting rods to strike the piston cooling jets. Damage or misalignment may occur.
Push the piston assemblies into the cylinder bores.
Illustration 4 g00541256
Attach lifting straps and a suitable lifting device to crankshaft (7) .
Lift crankshaft (7) out of the cylinder block. The weight of the crankshaft is 29 kg (65 lb). Do not scratch any of the finished surfaces on the crankshaft.
Illustration 5 g00541257
Remove upper main bearings (8) and upper thrust washers (9) from the cylinder block.
Cat SIS web machinery list:
Parts switch Caterpillar catalog:
10 FT, 10-20B, 10B, 120, 12E, 140, 14E, 16, 16G, 206, 212, 214B, 215, 224B, 225, 227, 235, 245, 518C, 528B, 530B, 615, 621B, 621R, 623, 627, 627B, 631C, 637, 637D, 641B, 657, 657B, 666, 666B, 8 FT, 8-...
245, 615, 777, D8L, D9L
225, 231D, 508, 613C, 621E, 621F, 623E, 627E, 627F, 631E, 637E, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 777B, 785, 789, 793, 824C, 826C, 953, 980C, D4H, D4HTSK II, E180, E240, E300, E300B, PR-...
225D, 231D, 776C, 980F II, CB-434, CS-531, CS-533, D4H, D4H XL, D4HTSK II, D4HTSK III, D7G, PR-450C, RR-250, SS-250
120G, 12G, 12H ES, 12H NA, 130G, 140G, 140H ES, 140H NA, 143H, 14G, 160G, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 245D, 578, 589, 611, 613C, 615, 615C, 621E, 621F, 623E, 627E, 627F, 631E, 637E, 651E, ...
120G, 12G, 130G, 14G, 16G, 621B, 627B, 633D, 637D, 641B, D6C, D8H, D9G
120G, 130G, 16G, 518, 615, 815B, 826C, 834B, 941, 943, 950B, 955L, 963, 966D, 980C, 988B, 992C, D10, D4E, D5B, D6D, D7G, R1700 II
120G, 12G, 130G, 140G, 14G, 160G, 16G, 613C, 615, 621E, 623E, 627E, 631E, 637E, 651E, 657E, 773B, 777, 777B, 784B, 785, 785B, 789, 789B, 793B, 814B, 815B, 824C, 825C, 826C, 916, 926, 926A, 936, 936F, ...
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 613C, 613C II, 615, 61...
613C, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777B, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 814B, 815B, 824C, 825C, 826C, 916...
621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 69D, 768C, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, ...
768C, 769C, 771C, 772B, 773B, 775B, 776C, 784B, 785, 785B, 789, 789B, 793B, 793C, 910E, 918F, 924F, 928F, 936F, 938F, 950F, 950F II, 960F, 966F, 966F II, 970F, 980F, 980F II, IT12B, IT14F, IT18F, IT24...
3N8335
SWITCH
D379, D398, D399
D379, D398, D399
4490802
SWITCH AS-START
C13, C9.3
C13, C9.3
4255230
SWITCH
C1.5, CB24B
C1.5, CB24B
3516B, 5130B, 5230, 5230B, 776D, 777, 777B, 777C, 777D, 784C, 785C, 785D, 789, 789C, 789D, 793C, 793D, 797, 797B, 994D, 994F, 994H, D11N, D11R
4302782
SWITCH
3512C
3512C
3978120
SWITCH-BUTTON
3512C
3512C
3N9598
SWITCH (oil pressure)
3306, D343
3306, D343
D343, D398
5L7111
SWITCH (TAP)
D342C, D343
D342C, D343
2L9634
SWITCH
D320A, D342, D342C, D353C
D320A, D342, D342C, D353C
8M0358
SWITCH ASSEM.
769, 955H, 977H, 977K, 983
769, 955H, 977H, 977K, 983
D320A, D353C, D399