AVSPARE.COM
parts catalog

SWITCH (heat start) 7N8002 - Caterpillar


7N8002 SWITCH (heat start) Caterpillar parts 225, 235, 245
Rating:
31
Alternative (cross code) number:
CA7N8002
7N-8002
7N8002
Caterpillar 7N8002 SWITCH (heat start)
Weight: 146 pounds 66 kg.

Buy SWITCH (heat start) 7N8002 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 7N8002:

EXCAVATOR  225   235   245   Caterpillar
Number on catalog scheme: 3
  For full view, you need register

Information:

Output Test
When an output test signal is received, the RDM activates all outputs for 10 seconds or until the test signal is deactivated. To do an output test, connect terminal 5 of the RDM to terminal 7 of the RDM with a jumper.When the data link malfunctions, R1 output (terminal 2 of RDM) will FLASH at a rate of 0.5 Hz. Relays R2 through R9 will either maintain their present state or default to OFF. This is controlled by a jumper between terminals 6 and 7 of the RDM. If a jumper is NOT present when the serial data link has a fault, the relay outputs (R2 through R9) will maintain their present state. If the jumper is present, R2 through R9 will default to OFF. Specifications:* The maximum distance between the RDM and the GSC+ is 305 m (1000 ft.).* The operating voltage range is from 15 to 45 DCV. The RDM is designed to operate when powered by only 24 or 32 DCV battery systems.* The RDM is capable of operating with or without an earth ground.* The RDM must share a common ground with the GSC+ and the relay board.* The terminals on the RDM are 6.4 mm (.25 in.) push on blade type connectors.* The terminals on the relay board are 6-32 screw terminals.* The driver outputs of the RDM are intended to drive incandescent lamps or relay loads. The driver outputs sink up to 600mA at 15 to 45 DCV and are protected against short circuits to B+ and B-.* The relay outputs of the relay board are protected by 1 amp fuses. The contacts are flashed silver and are rated at 1A at 28 DCV. The relay coils draw 20mA at 24 DCV. The GSC+ diagnoses a fault in the relay driver module circuit. See CID 475 in the topic Diagnostic Fault Codes of the Testing and Adjusting section. The CID 475 procedure also contains schematics for relay driver module installation purposes.Synchronizing Lights Module
Synchronizing Lights Module
(1) Synchronizing lights. (2) Synchronizing switch.The optional synchronizing lights (SL) module is located on the instrument panel (same location as for the optional alarm module). The SL module is not used when the panel is equipped with an electronic governor.Synchronizing lights (SL) are used as an aid in manually paralleling generator units independent of load. Each of two lights are connected across the generator to the load side of the generator output circuit breaker. The voltage of two phases are measured and the lights indicate when the voltages are in phase. When the voltages are in phase, closing the circuit breaker puts the generator on-line with the other generator unit(s). For a complete explanation on how to parallel two units, make reference to the Operation and Maintenance Manual for SR4B Generators and Control Panels, Form No. SEBU6918.Synchronizing Module Installation
To avoid electrical shock and personal injury, shut-down all on-line gensets before installing or repairing the synchronizing module.
For connection of the synchronizing light module and connection of resistor taps

Caterpillar parts catalog:

Caterpillar parts catalog
245 EXCAVATOR 82X00001-UP (MACHINE) POWERED BY 3406 ENGINE
235 EXCAVATOR 64R00596-01257 (MACHINE) POWERED BY 3306 ENGINE
235 EXCAVATOR 83X00001-00443 (MACHINE) POWERED BY 3306 ENGINE
235 EXCAVATOR 64R00596-01257 (MACHINE) POWERED BY 3306 ENGINE
235 EXCAVATOR 83X00001-00443 (MACHINE) POWERED BY 3306 ENGINE
235 EXCAVATOR 32K01301-02678 (MACHINE) POWERED BY 3306 ENGINE
235 EXCAVATOR 81X00001-UP (MACHINE) POWERED BY 3306 ENGINE
235 EXCAVATOR 64R00596-01257 (MACHINE) POWERED BY 3306 ENGINE
225 EXCAVATOR 76U01200-02728 (MACHINE) POWERED BY 3304 ENGINE
235 EXCAVATOR 64R00596-01257 (MACHINE) POWERED BY 3306 ENGINE
235 EXCAVATOR 83X00001-00443 (MACHINE) POWERED BY 3306 ENGINE


Parts switch Caterpillar catalog:

2G3903 SWITCH
215, 225, 227, 235, 245, 637D
7N4350 SWITCH ASSEM. (vacuum)
235, 235B, 235C, 245, 245B
7N4447 SWITCH ASSEM. (hyd. oil filter)
245, 245B, 245D, 5130, 5230, 776C, 777B, 784B, 785, 785B, 789, 789B, 793, 793B, D10, D11N, D11R
7N4446 SWITCH ASSEM. (hyd. oil filter)
235, 235B, 235C, 235D, 245, 245B, 245D, 777, 988
5C0744 SWITCH (push button)
215, 215B, 215D, 225, 229, 229D, 235, 235C, 235D, 245, 245B
4V9037 SWITCH ASSEM. (lights)
215, 225, 227, 235, 245, 651E, 657E, D8L
4V9040 SWITCH ASSEM.
215, 225, 235, 245, 834B, 953, 963, 966D, 973, 988B, 992C
4V9039 SWITCH ASSEM.
215, 225, 235, 245
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.