9R9868 SWITCH GP-PUSH BUTTON Caterpillar parts
414E, 416, 416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424B, 424D, 426B, 426C, 428B, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 434E, 434F, 436B, 436C, 438B, 438C, 438D, 442D, 446...
Rating:
Alternative (cross code) number:
CA9R9868
9R-9868
9R9868
CA9R9868
9R-9868
9R9868
Weight: 0.14 pounds 0 kg.
BACKHOE LOADER, VIBRATORY COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
15 Jul 2019
Unknown: Unknown
Caterpillar 9R9868 Switch A New
This part in 9 request:
Show.
This information for suppliers only!
2025-06-17
2024-03-04
2020-05-30
2019-12-03
2019-07-01
2018-07-29
2018-07-29
2018-07-21
2018-07-21
Number on catalog scheme:
29
For full view, you need register
Compatible equipment models: 9R9868:
Information:
Probable Causes
Failed turbocharger seals
Worn valve guide seals or faulty valve guide seals
Worn valve guides
Worn piston rings
Extended idle timesRecommended Actions
Note: After the repair has been made, the oil should be cleaned from the exhaust system. To clean the oil from the exhaust system, perform the following procedure:
Remove excess oil from piping with a clean cloth.
Operate the engine at elevated idle (1500 RPM) for 10 minutes.
Table 1
Troubleshooting Test Steps Values Results
1. Failed Turbocharger Seals
A. Check the inlet manifold and the exhaust manifold for oil.
Turbo seals
Result: Oil is present in the inlet or exhaust manifold.
Replace the turbocharger. Verify the repair.
Result: Oil is not present in the inlet or exhaust manifold.
Proceed to Test Step 2.
2. Worn Valve Guide Seals or Faulty Valve Guide Seals
A. Inspect the valve guide seals for wear and for damage.
Valve guide seals
Result: The valve guide seals are damaged.
Replace the valve guide seals. Verify the repair.
Result: The valve guide seals are not damaged.
Proceed to Test Step 3.
3. Worn Valve Guides
A. Inspect the valve guides for wear. Refer to the Specification manual for the maximum permissible wear of the valve guides.
Valve guides
Result: The valve guides are worn.
If necessary, recondition the cylinder head. Verify the repair.
Result: The valve guides are not worn.
Proceed to Test Step 4.
4. Worn Piston Rings
A. Piston rings that have excessive wear can cause too much pressure in the crankcase. The additional pressure in the crankcase will cause more than the normal amount of crankcase blowby from the crankcase breather.
B. Inspect piston rings
Piston rings
Result The piston rings are worn.
Replace the piston rings. Verify the repair.
Result The piston rings are not worn.
Proceed to Test Step 5.
5. Extended Idle Times
A. Extended idle times will allow oil to pass into the exhaust system.
Idle times
Result The idle times are extensive.
Reduce the idle times.
Complete the procedure in the order in which the steps are listed. If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Failed turbocharger seals
Worn valve guide seals or faulty valve guide seals
Worn valve guides
Worn piston rings
Extended idle timesRecommended Actions
Note: After the repair has been made, the oil should be cleaned from the exhaust system. To clean the oil from the exhaust system, perform the following procedure:
Remove excess oil from piping with a clean cloth.
Operate the engine at elevated idle (1500 RPM) for 10 minutes.
Table 1
Troubleshooting Test Steps Values Results
1. Failed Turbocharger Seals
A. Check the inlet manifold and the exhaust manifold for oil.
Turbo seals
Result: Oil is present in the inlet or exhaust manifold.
Replace the turbocharger. Verify the repair.
Result: Oil is not present in the inlet or exhaust manifold.
Proceed to Test Step 2.
2. Worn Valve Guide Seals or Faulty Valve Guide Seals
A. Inspect the valve guide seals for wear and for damage.
Valve guide seals
Result: The valve guide seals are damaged.
Replace the valve guide seals. Verify the repair.
Result: The valve guide seals are not damaged.
Proceed to Test Step 3.
3. Worn Valve Guides
A. Inspect the valve guides for wear. Refer to the Specification manual for the maximum permissible wear of the valve guides.
Valve guides
Result: The valve guides are worn.
If necessary, recondition the cylinder head. Verify the repair.
Result: The valve guides are not worn.
Proceed to Test Step 4.
4. Worn Piston Rings
A. Piston rings that have excessive wear can cause too much pressure in the crankcase. The additional pressure in the crankcase will cause more than the normal amount of crankcase blowby from the crankcase breather.
B. Inspect piston rings
Piston rings
Result The piston rings are worn.
Replace the piston rings. Verify the repair.
Result The piston rings are not worn.
Proceed to Test Step 5.
5. Extended Idle Times
A. Extended idle times will allow oil to pass into the exhaust system.
Idle times
Result The idle times are extensive.
Reduce the idle times.
Complete the procedure in the order in which the steps are listed. If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Cat SIS web machinery list:
Parts switch Caterpillar catalog:
414E, 416D, 416E, 420D, 420E, 422E, 424B, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 446D, 450E
611, 613C, 613C II, 615C, 621E, 621F, 623E, 623F, 627E, 627F, 631E, 633E II, 637E, 651E, 657E, 784B, 785, 785B, 789, 789B, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 797F, 902, 906, 908, 910G, 914G, ...
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 236D, 242D, 246C, 246D, 24M, 256C, 257D...
226B, 226B3, 232B, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247B, 247B3, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, 2...
902, 904B, 904H, 906, 908, C13, C15, C18, C9.3, CB-14, CB-214E, CB-22, CB-334E, CB-34, CB-434D, CB-44B, CB-534D, CB-54, CB-54B, CB-564D, CB-634D, CB-64, CD-54, CD-54B, CW-14, CX31-C13I, CX31-C15I, CX3...
3054C, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, 914G, C4.4, IT14G
3054C, 414E, 416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 914G, C4.4, IT14G
120M, 140M, 143H, 160M, 163H NA, 216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 242B, 242B3, 246C, 247B, 247B3, 24H, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 27...
416F, 420F, 422E, 422F, 428E, 428F, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450F, 906H, 906H2, 907H, 907H2, 908H, 908H2, 910K, 914K
215B, 245, 416, 426, 428, 436, 446, 508, 578, 589, 613C, 615, 615C, 651E, 657E, 773B, 777, 777B, 824C, 826C, 916, 926, 926A, 936, 936F, 980C, 994D, CS-643, D10N, D11N, D350E, D400E, D40D, D4H, D4HTSK ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, ...
416, 416B, 426, 426B, 428, 428B, 436, 914G, AP-200, AP-200B, IT14G
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 320B, 320C, 322C, 323D L, 32...
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16H NA, 24H, 323D L, 323D LN, 324D LN, 325D, 325D L, 330D, 330D L, 33...
1090, 1190, 1190T, 120K, 120K 2, 120M, 1290T, 12K, 1390, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 216, 2290, 236, 2390, 2391, 247, 2491, 24H, 24M, 2590, 267, 287, 30/30, 307B, 312B L, 315B L, 317B LN...
416B, 426B, 428B
1687557
SWITCH AS-PRESSURE
320C, 446B, 446D
320C, 446B, 446D
120G, 120H ES, 120H NA, 12G, 12H ES, 12H NA, 130G, 135H NA, 140G, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 24H, 446, 446B, 508, 994, 994D, D250D, D250E, D250E...
9W4139
SWITCH AS-PRESSURE
446, 446B
446, 446B
225, 231D, 235B, 235C, 235D, 416, 416B, 416C, 426B, 426C, 428, 428B, 428C, 436, 436C, 438C, 908, AP-1000B, AP-1055B, AP-800C, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C, CB-534, D250B, D300B, PR-100...
3D8754
SWITCH AS-TOGGLE
120G, 12E, 12G, 130G, 140G, 14E, 14G, 16, 16G, 215, 215B, 227, 235B, 245, 416B, 426, 428B, 436, 446B, 528B, 530B, 621, 621G, 623G, 627G, 631G, 633C, 637G, 641B, 657G, 814, 910, 931, 941, 950, 980, 988...
120G, 12E, 12G, 130G, 140G, 14E, 14G, 16, 16G, 215, 215B, 227, 235B, 245, 416B, 426, 428B, 436, 446B, 528B, 530B, 621, 621G, 623G, 627G, 631G, 633C, 637G, 641B, 657G, 814, 910, 931, 941, 950, 980, 988...
3116, 320 L, 3208, 320C, 320D, 320D FM, 320D L, 320D LN, 320D2, 320D2 L, 320E, 320E L, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D L, 324D LN, 324E L, 324E LN, 325, 325C, 325D, 325D...