0998031 T-JOINT Caterpillar parts
E240C, E300B, EL240B
Rating:
Alternative (cross code) number:
CA0998031
099-8031
0998031
CA0998031
099-8031
0998031
Weight: 0.27 pounds 0 kg.
EXCAVATOR,
Number on catalog scheme:
17
For full view, you need register
Information:
Removal Procedure
Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect". Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Illustration 1 g01467869
Disconnect hose assemblies (1), (4) and (5).
Remove two bolts (3) and pressure reducing valve (2). Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 2 g01467869
Install pressure reducing valve (2) and two bolts (3).
Connect hose assemblies (1), (4) and (5).
Purge the air from the parking brake. Refer to Systems Operation, Testing and Adjusting, "Braking System Air - Purge".
Fill the hydraulic tank with oil to the correct level. Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check".
Test the pressure reducing valve. Refer to Systems Operation, Testing and Adjusting, "Pressure Reducing Valve (Pilot Oil) - Test and Adjust". End By:
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect". Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Illustration 1 g01467869
Disconnect hose assemblies (1), (4) and (5).
Remove two bolts (3) and pressure reducing valve (2). Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 2 g01467869
Install pressure reducing valve (2) and two bolts (3).
Connect hose assemblies (1), (4) and (5).
Purge the air from the parking brake. Refer to Systems Operation, Testing and Adjusting, "Braking System Air - Purge".
Fill the hydraulic tank with oil to the correct level. Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check".
Test the pressure reducing valve. Refer to Systems Operation, Testing and Adjusting, "Pressure Reducing Valve (Pilot Oil) - Test and Adjust". End By:
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar parts catalog:
Parts t Caterpillar catalog:
311, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E70, EL240B
0951482
T-JOINT
E180, E240, E300, E300B, E650
E180, E240, E300, E300B, E650
E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300, E300B, E450, E650, E70, E70B, EL240B
0963808
T-JOINT
E110, E110B, E120, E120B, E140, E200B, E240C, E300, E650
E110, E110B, E120, E120B, E140, E200B, E240C, E300, E650
0963812
T-JOINT
E200B, E300B, EL200B, EL300B
E200B, E300B, EL200B, EL300B
0964628
T-JOINT
E110B, E120B, E200B, E300B
E110B, E120B, E200B, E300B
0854577
T-JOINT
E110B, E120B, E200B, E240C, E300B, E70B, EL240B
E110B, E120B, E200B, E240C, E300B, E70B, EL240B
0860457
T-JOINT
E110B, E120B, E200B, E240C, E300B, E70B, EL240B
E110B, E120B, E200B, E240C, E300B, E70B, EL240B
0855283
T-JOINT
E110B, E120B, E240C, E300B, EL240B
E110B, E120B, E240C, E300B, EL240B
0951479
T-JOINT
E300B
E300B
0995752
T-JOINT
E300B, E70B
E300B, E70B
E240C, E300B, EL240B
0995752
T-JOINT
E300B, E70B
E300B, E70B
0951479
T-JOINT
E300B
E300B
4I9192
T-JOINT
EL300B
EL300B
1R8629
T-JOINT
E200B, EL200B
E200B, EL200B
0855283
T-JOINT
E110B, E120B, E240C, E300B, EL240B
E110B, E120B, E240C, E300B, EL240B
0990462
T-JOINT
E110B, E120B
E110B, E120B
0995926
T-JOINT
E140
E140
0861652
T-JOINT
E240C, EL240B
E240C, EL240B
0998353
T-JOINT
EL240B
EL240B
1R7835
T-JOINT
E240C, E300B, EL240B
E240C, E300B, EL240B
0858597
T-JOINT
E240C, E300B, EL240B
E240C, E300B, EL240B
E240C, E300B, EL240B