1917524 TANK GP-WINDOW WASHER Caterpillar parts
303, 303.5E, 304, 304E, 305, 305.5, 305.5E, 305E, 306, 306E, 307E, 308E, 308E CR, 308E SR, 308E2 CR
Rating:
Alternative (cross code) number:
CA1917524
191-7524
1917524
CA1917524
191-7524
1917524
Weight: 0.79 pounds 0 kg.
MINI HYD EXCAVATOR,
Compatible equipment models: 1917524:
Information:
Illustration 2 g01041565
Attach the ground strap to the closest mounting bolt (2B) and to the Product Link Electronic Control Module (ECM).
Illustration 3 g01041573
Route harness (2E) through the cab floor. When possible, use an existing hole. Create a hole in the right hand side of the cab floor in order to route harness (2E) through, if no other hole is accessible.Note: A smaller hole can be made if the harness is routed from the inside of the cab to the outside of the cab.
Illustration 4 g01042855
Remove the 8 pin connector on the Product Link harness and replace with a 6 pin connector. Arrange the wires to correspond with the 6 pin connection on the machine platform harness. The connection is located under the right hand side of the platform.Note: Refer to the machines Electrical Schematic for the correct wire colors and numbers.
Illustration 5 g01044365
Location of the connector for the harness for the machine platform
Connect the Product Link harness (2E) to the machine harness.Note: The Product Link harness may be shortened as necessary. Excess length should be secured. The 9 pin connector section of the Product Link harness is not used and can be either shortened or discarded.
Illustration 6 g01041633
Connect the 24-pin connector of harness (2E) to the bottom of ECM (1) .
Illustration 7 g01041761
Route harness (2E) under the right hand side of the operator's console. Use tie straps in order to secure the harness inside the cab and underneath the cab.
Illustration 8 g01041766
The 207-6799 Antenna As (3 ft magnetic) is shown on a 12H Motor Grader.
Attach antenna (3) to the top, rear center of the cab. If a magnetic mount for the antenna is not used, a mounting bracket can be manufactured in order to hold the antenna in place.Note: The mounting of the antenna will vary slightly. When mounting an antenna without a magnetic mount, care must be taken to ensure that no structural certifications are invalidated. Take the appropriate measures in order to ensure that the following items do not void any structural certification:ROPS, FOPS and other protective structures. Refer to Special Instruction, SEHS6929, "Inspection, Maitenance and Repair of Rollover Protective Structures (ROPS) and Attachment Guidelines" as well as any other guidelines that have been published. Refer to Service Magazine, SEPD0558 15 01, "Correction to the Service Magazine, "Proper Communication Radio Installation Reduces Interference with Machine Electronics".
Route the harness for the antenna through the cab. When possible, use an existing hole that has a rubber grommet.Note: If no hole is present to route the harness for the antenna through, refer to Step 11.
Illustration 9 g01042971
Drill a 21 mm (0.8 inch) hole that is located 286 mm (11 inch) from the center of the cab and 100 mm (4 inch) from the top of the cab. Install a 5P-8525 Grommet in the hole. Route the harness for the antenna through the grommet.
Illustration 10 g01041776
Route harness (3) inside the cab. Use plastic self-adhesive clips in order to secure the harness. Ensure that the routing of the harness does not interfere with the operator's visibility.
Illustration 11 g01041781
Connect harness (3)
Cat SIS web machinery list:
Parts tank Caterpillar catalog:
3671051
TANK AS-HYDRAULIC
303.5E, 304E
303.5E, 304E
3671085
TANK AS-FUEL
305.5E, 305E
305.5E, 305E
3671071
TANK AS-HYDRAULIC
305.5E, 305E
305.5E, 305E
3777981
TANK AS-FUEL
308E, 308E2 CR
308E, 308E2 CR
3989773
TANK AS-FUEL
306E
306E
3863670
TANK GP-FUEL
307E, 308E
307E, 308E
3863671
TANK AS-FUEL
307E, 308E
307E, 308E
3863691
TANK AS-HYDRAULIC
307E, 308E
307E, 308E
3778001
TANK AS-FUEL
308E CR, 308E SR
308E CR, 308E SR
3778003
TANK AS-HYDRAULIC
308E CR, 308E SR
308E CR, 308E SR
3961842
TANK AS-HYDRAULIC
308E2 CR
308E2 CR
2417456
TANK AS-HYDRAULIC
304, 305
304, 305
2407602
TANK AS-FUEL
304, 305
304, 305
1848204
TANK AS-FUEL
312C
312C
2330973
TANK AS-HYDRAULIC
M318C, M318C MH
M318C, M318C MH
1939732
TANK AS-FUEL
318C, 319C
318C, 319C
1948897
TANK AS-FUEL
314C
314C
1831527
TANK AS-FUEL
308C
308C