1S2036 TANK Caterpillar parts
140B, 920, 930, 930R
Rating:
Alternative (cross code) number:
CA1S2036
1S-2036
1S2036
CA1S2036
1S-2036
1S2036
Weight: 71 pounds 32 kg.
MOTOR GRADER, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Information:
Remove Tachometer Drive
1. Remove overspeed contactor (1) from adapter assembly (4).2. Remove bolts (2) and the clamps, and remove adapter assembly (4) from cover assembly (3). 3. Remove bolts (5) and cover assembly (3) from the flywheel housing.4. Remove shaft (6) from the cover assembly. 5. If necessary, remove dowels (7), bearing (8) and the seal from cover assembly (3). 6. Remove bolt (10) and adapter (9).Install Tachometer Drive
1. Put adapter (9) in position on the camshaft drive gear, and install bolt (10) that holds it. Use the following procedure to install the camshaft drive gear.a. Clean camshaft taper with a lint free cloth saturated with solvent to remove excess oil. Then clean camshaft taper with a lint free alcohol wipe to remove any residue. If the wipe is dirty after cleaning the camshaft taper, clean again with new alcohol wipe until the wipe comes back clean. It is critical that the camshaft taper be very clean, dry and free of residue before assembly.b. Repeat step a for the remaining camshaft.c. Clean camshaft drive gear tapered bore with a lint free cloth saturated with solvent to remove excess oil. Then clean camshaft drive gear tapered bore with a lint free alcohol wipe to remove any residue. If the wipe is dirty after cleaning the camshaft drive gear tapered bore, clean again with new alcohol wipe until the wipe comes back clean. It is critical that the camshaft drive gear tapered bore be very clean, dry and free of residue before assembly.d. Repeat step 3 for remaining camshaft drive gear.e. Check that Camshafts are pinned.f. Check that the flywheel is pinned.g. Place gears on the camshafts and remove backlash by rotating the gears in the opposite direction of engine rotation. For STANDARD ROTATION engines, turn the cam gears CLOCKWISE. For REVERSE ROTATION engines, turn the cam gears COUNTER CLOCKWISE.h. Install Timing Ring, accessory drive gear or plate, if applicable. Ensure that the hole in the timing ring is properly seated on the locating pin.i. Tighten cam gear retaining bolts to a torque of 360 N m (265 lb ft).j. Mark a vertical line on the cam gear retainer bolt head.k. Place driver against cam gear retaining plate and ring solidly with hammer 3-4 times.l. Retorque the cam gear retaining bolt to 360 N m (265 lb ft).m. Repeat steps k and l until the mark on the bolt has turned a minimum of 1/4 turn.n. Cam gear installation is complete. 2. Make sure dowels (7) are installed in cover assembly (3) so they extend 6.0 0.5 mm (.24 .02 inch) above the surface of the cover assembly.3. If bearing (8) was removed from the cover assembly, install the bearing with tooling (A) until it is 26 1 mm (1.02 .04 in.) below the outside surface of the cover assembly. 4. If seal (11) was removed from the cover assembly, install the seal with tooling (A) until the seal makes contact with the bottom of the
1. Remove overspeed contactor (1) from adapter assembly (4).2. Remove bolts (2) and the clamps, and remove adapter assembly (4) from cover assembly (3). 3. Remove bolts (5) and cover assembly (3) from the flywheel housing.4. Remove shaft (6) from the cover assembly. 5. If necessary, remove dowels (7), bearing (8) and the seal from cover assembly (3). 6. Remove bolt (10) and adapter (9).Install Tachometer Drive
1. Put adapter (9) in position on the camshaft drive gear, and install bolt (10) that holds it. Use the following procedure to install the camshaft drive gear.a. Clean camshaft taper with a lint free cloth saturated with solvent to remove excess oil. Then clean camshaft taper with a lint free alcohol wipe to remove any residue. If the wipe is dirty after cleaning the camshaft taper, clean again with new alcohol wipe until the wipe comes back clean. It is critical that the camshaft taper be very clean, dry and free of residue before assembly.b. Repeat step a for the remaining camshaft.c. Clean camshaft drive gear tapered bore with a lint free cloth saturated with solvent to remove excess oil. Then clean camshaft drive gear tapered bore with a lint free alcohol wipe to remove any residue. If the wipe is dirty after cleaning the camshaft drive gear tapered bore, clean again with new alcohol wipe until the wipe comes back clean. It is critical that the camshaft drive gear tapered bore be very clean, dry and free of residue before assembly.d. Repeat step 3 for remaining camshaft drive gear.e. Check that Camshafts are pinned.f. Check that the flywheel is pinned.g. Place gears on the camshafts and remove backlash by rotating the gears in the opposite direction of engine rotation. For STANDARD ROTATION engines, turn the cam gears CLOCKWISE. For REVERSE ROTATION engines, turn the cam gears COUNTER CLOCKWISE.h. Install Timing Ring, accessory drive gear or plate, if applicable. Ensure that the hole in the timing ring is properly seated on the locating pin.i. Tighten cam gear retaining bolts to a torque of 360 N m (265 lb ft).j. Mark a vertical line on the cam gear retainer bolt head.k. Place driver against cam gear retaining plate and ring solidly with hammer 3-4 times.l. Retorque the cam gear retaining bolt to 360 N m (265 lb ft).m. Repeat steps k and l until the mark on the bolt has turned a minimum of 1/4 turn.n. Cam gear installation is complete. 2. Make sure dowels (7) are installed in cover assembly (3) so they extend 6.0 0.5 mm (.24 .02 inch) above the surface of the cover assembly.3. If bearing (8) was removed from the cover assembly, install the bearing with tooling (A) until it is 26 1 mm (1.02 .04 in.) below the outside surface of the cover assembly. 4. If seal (11) was removed from the cover assembly, install the seal with tooling (A) until the seal makes contact with the bottom of the
Caterpillar parts catalog:
Parts tank Caterpillar catalog:
3G9079
TANK ASSEM.
920, 930
920, 930
5V3704
TANK ASSEM.
920, 930
920, 930
5C7581
TANK ASSEM.
320C FM, 920
320C FM, 920
4V8161
TANK ASSEM.
920, 936, 950
920, 936, 950
2Y7135
TANK AS
930R
930R
5Y1788
TANK AS
930R
930R
1110566
TANK AS-FUEL
930R
930R
1110112
TANK AS
930R
930R
2P8683
TANK (Bottom)
627, 627B, 637B, 637D
627, 627B, 637B, 637D
7D5429
TANK ASSEM.
621, 627
621, 627
6A3304
TANK ASSEM.
920, 930, 966C, 966D, 966F
920, 930, 966C, 966D, 966F
1S7882
TANK ASSEM.
641, 651, 657, 666
641, 651, 657, 666