AVSPARE.COM
parts catalog

TANK GP 3233805 - Caterpillar



3233805 TANK GP Caterpillar parts TANK
Rating:
61
Alternative (cross code) number:
CA3233805
323-3805
3233805
Caterpillar 3233805 TANK GP

Buy TANK GP 3233805 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Install a small piece of reflective tape (14) from Tool (A) on tamper shaft (15).Test Procedure
Illustration 10 g06060804
Move machine power switch (13) into the ON position. After the home screen is shown on display (16), press, and hold push to start switch (12). Release the switch when the engine starts.
Illustration 11 g06060818
Actuate screen unlock switch (17) to enable the touch screen on the display.Note: When the display is enabled, an LED next to the screen unlock switch is illuminated.
Illustration 12 g06060825
Tap status icon (18) to enter the status screen.
Illustration 13 g06060828
Operate the engine at low idle for a few minutes. Press rpm increase switch (19) once to operate the engine in high idle.
Illustration 14 g06065149
Monitor the hydraulic oil temperature on display (20). Operate the machine until the oil temperature reaches a minimum of 45 10 °C (113 18 °F).
Tap compaction icon (21).
Illustration 15 g06064221
If "AUTO" (24) appears next to tamper icon (22), go to the next step. If the manual icon appears next to the tamper icon, go to Step 13.
Tap settings icon (23).
Illustration 16 g06065367
Tap"Tamper" (25).
Illustration 17 g06065372
Tap"Auto Speed" (26).
Illustration 18 g06065381
Tap"Disable" (27).
Tap back icon (28) three times.
Illustration 19 g06064249
If tamper icon (29) is gray and on the left side of the box, tap the icon. If the tamper icon is green and on the right side of the box, go to the next step.
Illustration 20 g06065403Note: The above illustration shows the left screed operator panel. The right screed operator panel is similar and can also be used.
Actuate mode select switch (31) until tamper mode indicator (30) is illuminated.
Rotate rotary dial (32) clockwise until all indicators (33) are illuminated.
Illustration 21 g06065408
Tamper speed (34) on the display should be 1800 rpm.
Illustration 22 g06065413
Squeeze trigger (35), and move propel lever (4) into the forward range.
Use Tool (A) to record the tamper speed. Refer to the specifications section above for the tamper speed specification.
Move propel lever (4) into the NEUTRAL position.
Press rpm decrease switch (10) once to operate the engine in low idle.Note: If necessary, perform a regeneration cycle before the engine is stopped.
Press and hold push to start switch (12). Release the switch when the engine stops.
Move machine power switch (13) to the OFF position.
Analyze the recorded speed reading. The speed specification is given in the specifications section above. If the tamper speed reading was within the specified ranges, the system is operating within design parameters. If tamper speed is less than the specified range, calibrate the tamper. Refer to Systems Operation Testing and Adjusting, Solenoid Valve (Tamper) - Calibrate.


Parts tank Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.