AVSPARE.COM
parts catalog

TANK GP-LINES& 3254273 - Caterpillar



3254273 TANK GP-LINES& Caterpillar parts TANK
Rating:
61
Alternative (cross code) number:
CA3254273
325-4273
3254273
Caterpillar 3254273 TANK GP-LINES&

Buy TANK GP-LINES& 3254273 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 8 g06228749
Ensure that the right side plate and the left side plate are in the float mode. The indicator light under each side plate lower buttons (8) and (9) should be on. If either side plate is locked, push the corresponding side plate button.
Place protective material under the rotor to prevent damage to the rotor bits or the work surface.
Illustration 9 g06228756
Observe level indicator (10). If the indicator shows "0" go to Step 15. If the indicator does not show "0", go to Step 13.
Illustration 10 g06295660
Use rear leg height switches (11) and (12) to level the rear of the machine. Level indicator (10) will show "0" when the rear of the machine is level.
Use moldboard lower button (13) to lower the moldboard to the lowest position.
Use front leg lower button (15) and rear leg lower button (14) until the side plates are just touching the surface. Insure the rotor tips are not touching the surface. The rotor tips should be at least 25.4 mm (1 inch) from the surface.Note: The rotor will move during this procedure. Make personnel and equipment are clear of the area around the cutter box.
Illustration 11 g06295666
Ensure that the engine is operating in low idle. The high idle indicator light should be off. If this indicator is illuminated, press throttle control button (16) to operate the engine in low idle.
Illustration 12 g06295668
Move engine start switch (17) to the OFF position.
Illustration 13 g06295673
Remove the right and left rubber floor mats from operator platform. Remove six bolts and washers (18) and remove left platform center cover plate (19).
Remove eight bolts and washers (20) and remove right platform center cover plate (21).Note: The center valve is located beneath left platform center cover plate (19). The rear valve is located beneath right platform center cover plate (21). Remove both plates to allow access for adjustments to either valve.
Illustration 14 g06295679
Typical example
Note: Illustration 14 shows a track tension valve attached to the center valve. Wheeled machines will not have a track tension valve attached to the center valve.
Remove cap from port "M1" (22) on the center valve. Connect Tool (A2) to the pressure tap in port "M1".
Clean and inspect the rotor to insure there is no loose debris is present. Insure all rotor tools and paddles are secure.Test Procedure
Move engine start switch (16) to the START position. Release the switch when the engine starts.
Operate the engine at low idle for a few minutes. Press throttle control button (15) to operate the engine in high idle.Note: The LED next to throttle control button (15) will be illuminated.
Illustration 15 g06295688
Monitor hydraulic oil temperature (23) on the operator display. Operate the machine until the oil temperature reaches the test temperature listed in the "Specifications"section.
Illustration 16 g06295700
Press and hold rotor button (6) for approximately 2 seconds to engage the rotor. Indicator (24) next to the rotor button illuminates when the rotor is engaged.Note: Engine speed will automatically return to low idle before the rotor engages.
Record pressure on Tool (A1) after the pressure stabilizes. The pressure will stabilize after a few


Parts tank Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.