AVSPARE.COM
parts catalog

TANK & BASE GP-FUEL 3340485 - Caterpillar



3340485 TANK & BASE GP-FUEL Caterpillar parts C18 TANK
Rating:
41
Alternative (cross code) number:
CA3340485
334-0485
3340485
Caterpillar 3340485 TANK & BASE GP-FUEL

Buy TANK & BASE GP-FUEL 3340485 Caterpillar genuine, new aftermarket tractor parts with delivery
GENERATOR SET,

Compatible equipment models: 3340485:

GENERATOR SET  C18   Caterpillar
  For full view, you need register

Information:


Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
D     127-4904     Repair Stand     1    
E     1P-0808     Multipurpose Grease     1    
F     5P-3520     Spanner Wrench     1    
G     7M-7456     Bearing Mount Compound     1    
H     195-4609     Seal Pick     1    
J     5P-4197     Spacer     1    
3S-6224 Electric Hydraulic Pump Gp     1    
FT-3035 Puller Plate     1    
6V-3160 Double Acting Cylinder     1    
9U-6833 Nut     1    
4C-9633 Puller Stud     1    
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed.Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death.Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 4 g01206581
(1) Apply Tooling (E) to the threads and tighten the nut to a torque of 650 50 N m (479 37 lb ft). (2) Apply Tooling (E) to the threads and tighten the head to a torque of 450 50 N m (332 37 lb ft). (3) Apply Tooling (G) to the seal groove prior to installation of the wiper seal. (4) Lubricate the seals with the lubricant that is being sealed.Installation Procedure
Table 3
Required Tools    
Tool    Part Number    Part Description    Qty    
C     1P-1859     Retaining Ring Pliers     1    Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 5 g01184857
Attach a suitable lifting device to stick cylinder

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts tank Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.