3540196 TANK GP-LUBRICATION Caterpillar parts
14M
Rating:
Alternative (cross code) number:
CA3540196
354-0196
3540196
CA3540196
354-0196
3540196
Weight: 36 pounds 16 kg.
MOTOR GRADER,
Compatible equipment models: 3540196:
Number on catalog scheme:
39
For full view, you need register
Information:
covers that are called out in illustration 2 in order to access the components that have power supplied by the ECM power supply.
As instructed in the "Power Train Electrical System Service Shutdown" procedure, use the high voltage meter to measure for any voltage between the high voltage bus connections in each of the open compartments. Verify that there is less than 50.0 VDC between all of the connections. Once the voltage level is verified, continue to the next step.
Turn the battery disconnect switch to the ON position. Turn the key start switch to the ON position. Do not start the engine.
Verify that the power supply diagnostic code is still active. Note: In the next steps, the components will be disconnected one at a time with the ECM powered in order to eliminate the components as the cause of this problem.
Refer to the connection diagram at the beginning of this procedure in order to determine the components that are powered by the ECM negative (-) 15.0 VDC power supply. While monitoring the status of the diagnostic code, individually disconnect each component one at a time. If the diagnostic code clears when a component is disconnected, replace the component. After all of the components are disconnected, check the status of the active power supply diagnostic code. If the diagnostic code is still active, proceed to the next step.
Turn the battery disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness connector J2 from the Motor 1 ECM. Examine the pins and sockets on the ECM and on the J2 connector. Ensure that all of the pins and sockets are secured in the connector, the contacts are clean, and the contacts are in good condition.
Disconnect the machine harness connector J2 from the Motor 2 ECM. Examine the pins and sockets on the ECM and on the J2 connector. Ensure that all of the pins and sockets are secured in the connector, the contacts are clean, and the contacts are in good condition.
At the J2 harness connector for the Motor 1 ECM, measure the resistance
As instructed in the "Power Train Electrical System Service Shutdown" procedure, use the high voltage meter to measure for any voltage between the high voltage bus connections in each of the open compartments. Verify that there is less than 50.0 VDC between all of the connections. Once the voltage level is verified, continue to the next step.
Turn the battery disconnect switch to the ON position. Turn the key start switch to the ON position. Do not start the engine.
Verify that the power supply diagnostic code is still active. Note: In the next steps, the components will be disconnected one at a time with the ECM powered in order to eliminate the components as the cause of this problem.
Refer to the connection diagram at the beginning of this procedure in order to determine the components that are powered by the ECM negative (-) 15.0 VDC power supply. While monitoring the status of the diagnostic code, individually disconnect each component one at a time. If the diagnostic code clears when a component is disconnected, replace the component. After all of the components are disconnected, check the status of the active power supply diagnostic code. If the diagnostic code is still active, proceed to the next step.
Turn the battery disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness connector J2 from the Motor 1 ECM. Examine the pins and sockets on the ECM and on the J2 connector. Ensure that all of the pins and sockets are secured in the connector, the contacts are clean, and the contacts are in good condition.
Disconnect the machine harness connector J2 from the Motor 2 ECM. Examine the pins and sockets on the ECM and on the J2 connector. Ensure that all of the pins and sockets are secured in the connector, the contacts are clean, and the contacts are in good condition.
At the J2 harness connector for the Motor 1 ECM, measure the resistance
Caterpillar parts catalog:
Parts tank Caterpillar catalog:
120K, 120K 2, 120M, 12K, 12M, 140K, 140K 2, 140M, 14M, 160K, 160M, 953D, 963D, 973D, AP-600D, AP-655D, AP555E, BG500E, BG600D, BG655D, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-68B, C...
2540079
TANK-WASHER
120M, 12M, 140M, 14M, 160M, 16M
120M, 12M, 140M, 14M, 160M, 16M
3559823
TANK AS-WINDOW WASHER
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M
2413868
TANK AS-HYDRAULIC
120M, 12M, 140M, 14M, 160M
120M, 12M, 140M, 14M, 160M
2466651
TANK-AIR
120M, 12M, 140M, 14M, 160M
120M, 12M, 140M, 14M, 160M
3708692
TANK AS-HYDRAULIC
Caterpillar
Caterpillar
3770294
TANK-WATER
Caterpillar
Caterpillar
2270411
TANK AS-HYDRAULIC
365C, 365C L, 365C L MH, 374D L
365C, 365C L, 365C L MH, 374D L
3166405
TANK AS-HYDRAULIC
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD
3612116
TANK GP-FUEL
120M
120M
2770460
TANK AS-FUEL
160K
160K
3959271
TANK GP-HYDRAULIC
MH3049
MH3049
3959726
TANK AS-FUEL
MH3037, MH3049, MH3059
MH3037, MH3049, MH3059
4400075
TANK AS
MH3037
MH3037
3829822
TANK AS-FUEL
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
3829798
TANK AS-FUEL
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
3836365
TANK AS-FUEL
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD