5688688 TANK GP-FUEL Caterpillar parts
Rating:
Alternative (cross code) number:
CA5688688
568-8688
5688688
CA5688688
568-8688
5688688
Weight: 87 pounds 39 kg.
Information:
1. Remove nuts (1), cover (2), and the gasket. 2. Remove four bolts (3) and automatic timing advance (4). Remove the O-ring seals from the automatic timing advance. 3. Remove gear (6) from fuel injection pump camshaft (5).Install Automatic Timing Advance
1. Remove the plug from the timing pin hole in the fuel injection pump housing, and install Tool (A) in the timing pin hole.2. Install two 7/16"-20 NF x 4"long bolts in fuel injection pump camshaft (1). Slowly rotate the fuel injection pump until Tool (A) goes into the groove in the fuel injection pump camshaft. Remove the bolts from the camshaft. 3. Put No. 1 piston at the top center compression position (TC) with the following procedure:a. Remove plug (3), timing bolt (4) and cover (2) from the flywheel housing. b. Install Tool (B) in the flywheel housing. Use Tool (B) to slowly rotate the engine in the direction of normal rotation (counterclockwise as seen from the flywheel end of the engine) until timing bolt (4) can be installed in the flywheel housing and into the hole in the flywheel. c. Remove the valve cover from the valve cover base. Check to see if both rocker arms (5) for the No. 1 cylinder can be moved backward and forward. The No. 1 piston is at the top center compression position (TC) when the timing bolt is installed in the flywheel and both rocker arms for the No. 1 cylinder can be moved backward and forward. If both rocker arms cannot be moved, the No. 1 piston is not at the top center compression position (TC). Remove the timing bolt from the flywheel and rotate the engine in the direction of normal rotation (counterclockwise as seen from the flywheel end of the engine) one full turn 360 degrees,and install the timing bolt again.4. Remove the timing bolt, and use Tool (B) to rotate the engine in the opposite direction of normal rotation (clockwise as seen from the flywheel end of the engine) a minimum of 30 degrees. 5. Put gear (6) in position on the fuel injection pump camshaft. 6. Put two O-ring seals (8) in position on automatic timing advance (7).7. Put automatic timing advance in position on the fuel injection pump camshaft, and install the four bolts. Tighten the bolts to a torque of 3 N m (27 lb in).8. Use Tool (B) and slowly rotate the engine in the direction of normal rotation until the timing bolt can be installed in the flywheel.9. Tighten the bolts that hold the automatic timing advance to the fuel injection pump camshaft to a torque of 55 7 N m (41 5 lb ft).10. Remove Tool (A) from the fuel injection pump housing, and remove the timing bolt from the flywheel.11. Check the timing as follows:a. Rotate the engine in the direction of normal rotation (counterclockwise as seen from the flywheel end of the engine) two full turns, and install Tool (A) and the timing pin again.b.
1. Remove the plug from the timing pin hole in the fuel injection pump housing, and install Tool (A) in the timing pin hole.2. Install two 7/16"-20 NF x 4"long bolts in fuel injection pump camshaft (1). Slowly rotate the fuel injection pump until Tool (A) goes into the groove in the fuel injection pump camshaft. Remove the bolts from the camshaft. 3. Put No. 1 piston at the top center compression position (TC) with the following procedure:a. Remove plug (3), timing bolt (4) and cover (2) from the flywheel housing. b. Install Tool (B) in the flywheel housing. Use Tool (B) to slowly rotate the engine in the direction of normal rotation (counterclockwise as seen from the flywheel end of the engine) until timing bolt (4) can be installed in the flywheel housing and into the hole in the flywheel. c. Remove the valve cover from the valve cover base. Check to see if both rocker arms (5) for the No. 1 cylinder can be moved backward and forward. The No. 1 piston is at the top center compression position (TC) when the timing bolt is installed in the flywheel and both rocker arms for the No. 1 cylinder can be moved backward and forward. If both rocker arms cannot be moved, the No. 1 piston is not at the top center compression position (TC). Remove the timing bolt from the flywheel and rotate the engine in the direction of normal rotation (counterclockwise as seen from the flywheel end of the engine) one full turn 360 degrees,and install the timing bolt again.4. Remove the timing bolt, and use Tool (B) to rotate the engine in the opposite direction of normal rotation (clockwise as seen from the flywheel end of the engine) a minimum of 30 degrees. 5. Put gear (6) in position on the fuel injection pump camshaft. 6. Put two O-ring seals (8) in position on automatic timing advance (7).7. Put automatic timing advance in position on the fuel injection pump camshaft, and install the four bolts. Tighten the bolts to a torque of 3 N m (27 lb in).8. Use Tool (B) and slowly rotate the engine in the direction of normal rotation until the timing bolt can be installed in the flywheel.9. Tighten the bolts that hold the automatic timing advance to the fuel injection pump camshaft to a torque of 55 7 N m (41 5 lb ft).10. Remove Tool (A) from the fuel injection pump housing, and remove the timing bolt from the flywheel.11. Check the timing as follows:a. Rotate the engine in the direction of normal rotation (counterclockwise as seen from the flywheel end of the engine) two full turns, and install Tool (A) and the timing pin again.b.
Caterpillar SIS machinery equipment:
Caterpillar SIS
330 & 330 GC Excavators GDW00001-UP (MACHINE) POWERED BY C7.1 Engine »
568-8688
TANK GP-FUEL
330 & 330 GC Excavators FEK00001-UP (MACHINE) POWERED BY C7.1 Engine »
568-8688
TANK GP-FUEL
330 & 330 GC Excavators NDH00001-UP (MACHINE) POWERED BY C7.1 Engine »
568-8688
TANK GP-FUEL
330 Excavator WCH00001-UP (MACHINE) POWERED BY C7.1 Engine »
568-8688
TANK GP-FUEL
Caterpillar parts catalog:
Parts tank Caterpillar catalog:
5549412
TANK GP-COOLANT
Caterpillar
Caterpillar
5489198
TANK AS-HYDRAULIC
Caterpillar
Caterpillar
5406379
TANK GP-FUEL
Caterpillar
Caterpillar
5406378
TANK GP-FUEL
Caterpillar
Caterpillar
5406376
TANK GP-FUEL
Caterpillar
Caterpillar
5406375
TANK GP-FUEL
Caterpillar
Caterpillar
3496874
TANK-WATER
Caterpillar
Caterpillar
3261146
TANK
Caterpillar
Caterpillar
3237235
TANK-WASHER
Caterpillar
Caterpillar
3079601
TANK GP-FUEL
Caterpillar
Caterpillar
3048242
TANK-HYDRAULIC
Caterpillar
Caterpillar
3048239
TANK-FUEL
Caterpillar
Caterpillar