2297151 TIP-BUCKET Caterpillar parts
365C, 365C L, 374D L, 385C, 385C FS, 385C L, 390D, 390D L
Rating:
Alternative (cross code) number:
CA2297151
229-7151
2297151
CA2297151
229-7151
2297151
Weight: 80 pounds 36 kg.
EXCAVATOR, FRONT SHOVEL,
Compatible equipment models: 2297151:
Number on catalog scheme:
2
For full view, you need register
Information:
Machine Operating Temperature Range
The standard machine configuration is intended for use within an ambient temperature range of -18 °C (0 °F) to 50 °C (122 °F). Special configurations for different ambient temperatures may be available. Optional cold weather starting capability will allow the machine to start at -32 °C (-25 °F). Consult your Caterpillar dealer for additional information on special configurations of your machine.Operating the Machine
Only operate the machine while you are in a seat. The seat belt must be fastened while you operate the machine. Only operate the controls while the engine is running.Check for proper operation of all controls and protective devices while you operate the machine slowly in an open area.Before you move the machine, make sure that no one will be endangered.Do not allow riders on the machine unless the machine has the following equipment:
additional seat
additional seat belt
Rollover Protective Structure (ROPS)Report any needed repairs that were noted during operation.Carry attachments close to the ground, approximately 40 cm (15 inches) higher than ground level. Do not go close to the edge of a cliff, an excavation, or an overhang.If the machine begins to sideslip, perform the following procedure:
Discard the load.
Turn the machine downhill.Be careful to avoid any condition which could lead to tipping. Tipping can occur when you work on hills, banks and slopes. Also, tipping can occur when you cross ditches, ridges or other unexpected obstructions.Whenever it is possible, operate the machine up the slopes and down the slopes. Avoid operating the machine across the slope, when possible.Keep the machine under control. Do not overload the machine beyond capacity.Be sure that the towing devices are adequate.Never straddle a wire cable or allow other personnel to straddle a wire cable.Know the maximum dimensions of your machine.Always keep the Rollover Protective Structure (ROPS) installed during machine operation.
The standard machine configuration is intended for use within an ambient temperature range of -18 °C (0 °F) to 50 °C (122 °F). Special configurations for different ambient temperatures may be available. Optional cold weather starting capability will allow the machine to start at -32 °C (-25 °F). Consult your Caterpillar dealer for additional information on special configurations of your machine.Operating the Machine
Only operate the machine while you are in a seat. The seat belt must be fastened while you operate the machine. Only operate the controls while the engine is running.Check for proper operation of all controls and protective devices while you operate the machine slowly in an open area.Before you move the machine, make sure that no one will be endangered.Do not allow riders on the machine unless the machine has the following equipment:
additional seat
additional seat belt
Rollover Protective Structure (ROPS)Report any needed repairs that were noted during operation.Carry attachments close to the ground, approximately 40 cm (15 inches) higher than ground level. Do not go close to the edge of a cliff, an excavation, or an overhang.If the machine begins to sideslip, perform the following procedure:
Discard the load.
Turn the machine downhill.Be careful to avoid any condition which could lead to tipping. Tipping can occur when you work on hills, banks and slopes. Also, tipping can occur when you cross ditches, ridges or other unexpected obstructions.Whenever it is possible, operate the machine up the slopes and down the slopes. Avoid operating the machine across the slope, when possible.Keep the machine under control. Do not overload the machine beyond capacity.Be sure that the towing devices are adequate.Never straddle a wire cable or allow other personnel to straddle a wire cable.Know the maximum dimensions of your machine.Always keep the Rollover Protective Structure (ROPS) installed during machine operation.
Caterpillar parts catalog:
Parts tip Caterpillar catalog:
345C L, 375, 385B, 385C, 385C FS, 385C L, 5080, 5090B, 5130, 992C, 992D, 994
345C L, 385B, 385C, 385C FS, 385C L, 390D, 5080, 5090B, 5130, 992C, 992D, 992G, 994
385B, 390D, 994, 994D, 994F
235, 235C, 235D, 245, 245D, 330, 330 L, 330B L, 330C L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E, 350, 365B, 365B II, 365B L, 365C, 365C L, 375, 375 L, 385B, 5110B, 5130, 5130B,...
235, 235C, 235D, 245, 245D, 328D LCR, 330, 330 L, 330B L, 330C L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 350, 365B, 365B II, 365B L, 365C, 365C L, 375, 375 L, 385B, 988F, 988F II, ...
345C L, 350, 365B, 365B II, 365C, 365C L, 374D L, 375, 375 L, 385C, 385C L, 5080, 980G, 988H, 988K, 992G
375 L, 385B, 385C, 385C FS, 385C L, 5080, 992C, 992G, 994, 994D, 994F
345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 385C L, 390D, 5080, 5110B, 992G
345B II, 345C L, 350, 365B, 365B II, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 385C L, 5080, 992G
345C L, 365B, 365B II, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 385C L, 5080, 5110B, 992G
365B, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 5090B
324D, 330C L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 365B II, 365C, 365C L
330D L, 345C, 349E L, 349E L VG, 365B
330D L, 345C, 349E L, 349E L VG, 365B
2227553
TIP-TWIN SHARP
330C L, 345B II, 345C
330C L, 345B II, 345C
345B II, 345C L, 365B, 365B II, 365C, 365C L, 374D L, 385B, 385C, 385C L
1433095
TIP-SHARP
365B
365B
6Y0234
TIP
E650
E650
E110, E110B, E120B, E140, E200B
0859784
TIP
E120, E140
E120, E140
2227603
TIP-TWIN SHARP
374D L
374D L
2322137
TIP-SHORT
345C, 345D, 345D L, 349D, 349D L
345C, 345D, 345D L, 349D, 349D L
330D L, 345C, 349E L, 349E L VG