2320179 TIP-GENERAL PURPOSE Caterpillar parts
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 993K, 994F
Rating:
Alternative (cross code) number:
CA2320179
232-0179
2320179
CA2320179
232-0179
2320179
Weight: 88 pounds 40 kg.
EXCAVATOR, WHEEL LOADER,
Compatible equipment models: 2320179:
Number on catalog scheme:
2
For full view, you need register
Information:
Removal Procedure
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hoses and on all hose assemblies for installation purposes. Plug all hose assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g01322019
Raise the lift arms and position the cylinder lock (1) .
Tilt the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Drain the hydraulic tank into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change".
Illustration 2 g01363162
Disconnect hose assemblies (2) and (3) from gear pump (4) .
Disconnect hose assembly (6) .
Disconnect hose (7) .
Remove bolts (5) and remove gear pump (4) .
Illustration 3 g01363179
Remove O-ring seal (8) and remove coupler (9) .
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hoses and on all hose assemblies for installation purposes. Plug all hose assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g01322019
Raise the lift arms and position the cylinder lock (1) .
Tilt the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Drain the hydraulic tank into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change".
Illustration 2 g01363162
Disconnect hose assemblies (2) and (3) from gear pump (4) .
Disconnect hose assembly (6) .
Disconnect hose (7) .
Remove bolts (5) and remove gear pump (4) .
Illustration 3 g01363179
Remove O-ring seal (8) and remove coupler (9) .
Caterpillar parts catalog:
Parts tip Caterpillar catalog:
245B, 330, 330 L, 330B L, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 350, 365B, 365B L, 375, 375 L, 385B, 988F II, 988G, 988H, 990 II, 992C, 992D, 992G
235, 235C, 235D, 245, 245D, 330, 330 L, 330B L, 330C L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E, 350, 365B, 365B II, 365B L, 365C, 365C L, 375, 375 L, 385B, 5110B, 5130, 5130B,...
235, 235C, 235D, 245, 245D, 328D LCR, 330, 330 L, 330B L, 330C L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 350, 365B, 365B II, 365B L, 365C, 365C L, 375, 375 L, 385B, 988F, 988F II, ...
345C L, 350, 365B, 365B II, 365C, 365C L, 374D L, 375, 375 L, 385C, 385C L, 5080, 980G, 988H, 988K, 992G
375 L, 385B, 385C, 385C FS, 385C L, 5080, 992C, 992G, 994, 994D, 994F
994, 994D, 994F
345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 385C L, 390D, 5080, 5110B, 992G
345B II, 345C L, 350, 365B, 365B II, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 385C L, 5080, 992G
345C L, 365B, 365B II, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 385C L, 5080, 5110B, 992G
374D L, 374F L, 385C, 385C FS, 385C L, 390D, 390D L, 992K, 994F
365B, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 5090B
2642171
TIP-EXTRA-DUTY
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 993K, 994F
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 993K, 994F
349E L, 349E L VG, 990H, 990K, 992G, 992K
2322178
TIP-ABRASION
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 993K, 994F
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 993K, 994F
2297156
TIP-ABRASION
365C, 365C L, 374D L, 385C, 385C FS, 385C L, 390D, 390D L, 990 II, 990H, 990K, 992G, 992K
365C, 365C L, 374D L, 385C, 385C FS, 385C L, 390D, 390D L, 990 II, 990H, 990K, 992G, 992K
1711654
TIP-TWIN SHARP
365B, 5080, 992G
365B, 5080, 992G
1711655
TIP-SHORT
365B, 5080, 990 II, 992G
365B, 5080, 990 II, 992G
330D L, 336D L, 336D2 L, 345C, 345C L, 345D L, 345D L VG, 349D L, 349E L, 349E L VG, 365C, 365C L, 988H, 988K, 990 II, 990H, 990K
349E L, 349E L VG, 365C, 365C L, 374D L, 385C, 385C FS, 385C L, 390D, 390D L, 990 II, 990H, 992G, 992K
324D L, 325D L, 330C L, 330D L, 345C, 966G II, 966H, 972G II, 972H, 980G II, 980H, 980K, 980M, 982M
2320172
TIP-PENETRATION
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 994F
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 994F
2297152
TIP-PENETRATION
349E L, 349E L VG, 365C, 365C L, 374D L, 385C, 385C FS, 385C L, 390D, 390D L, 990 II, 990H, 990K, 992G, 992K
349E L, 349E L VG, 365C, 365C L, 374D L, 385C, 385C FS, 385C L, 390D, 390D L, 990 II, 990H, 990K, 992G, 992K
1711651
TIP-PENETRATION
365B, 5080, 992G
365B, 5080, 992G