TIP GP-PENETRATION 3814093 - Caterpillar

3814093 TIP GP-PENETRATION Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA3814093
381-4093
3814093

Weight: 42 pounds 19 kg.

Buy TIP GP-PENETRATION 3814093 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Temperature Transmitter Module,Temperature Transmitter Module Pt100 Dc 24v Output 0-10v -50 to 400 Degree with 1m Temperature Sensor

$22.49

09 Sep 2021
0.1124[0.05] Pounds
CN: PANGgu

Temperature Transmitter Module,Temperature Transmitter Module Pt100 Dc 24v Output 0-10v -50 to 400 Degree with 1m Temperature Sensor
Naisde OUTPUT : the output is in linear relation with input or temperature || STABLE PERFORMANCE: the temperature transmitter module made of stable electronic components with excellent working performance || STANDARD : send the corresponding standard (0-10v) value according to the range of the thermal resistance || HIGH SENSITIVE: the -50~400 degree temperature transmitter sensor has good sensitivity and quick respond || TEMPERATURE CALCULATION: this temperature transmitter calculate the current temperature by confirming that the resistance is different

This part in 2 request: Show. This information for suppliers only!

#677416 381-4093

2021-06-30

#568107 3814093

2020-12-05

Number on catalog scheme:

Caterpillar 3814093 Parts scheme TIP GP-PENETRATION

For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 7H-1942 Dial Indicator 1
- Magnetic Base and Stand 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If any part of the engine oil pump is worn or damaged, the complete assembly of the engine oil pump must be replaced.
Ensure that all components of the engine oil pump are clean and free from wear and damage. Refer to System Operation, Testing and Adjusting, "Engine Oil Pump - Inspect" for more information. Replace the complete assembly of the engine oil pump if any of the components are worn or damaged.
Illustration 1 g03409497
If necessary, follow Step 2.a through step 2.d to install cross over tube assembly (14).
Install new gasket (17) and new gasket (18).
Position cross over tube assembly (14) onto the cylinder block.
Install bolts (15) and bolts (16) to cross over tube assembly (14) finger tight.
Tighten bolts (15) and bolts (16) to a torque of 22 N m (195 lb in).
Illustration 2 g03409496
If necessary, follow Step 3.a through step 3.d to assemble engine oil pump assembly (2).
Lubricate the internal components for the assembly of the engine oil pump with clean engine oil.
Install outer rotor (13) to oil pump assembly (2). Ensure that the outer rotor is installed in the outer rotor original position and orientation.
Install front cover assembly (12) to engine oil pump assembly (2).
Install bolts (11) finger tight. Tighten the bolts to a torque of 22 N m (195 lb in).
Ensure that dowel (9) and dowel (10) are correctly located in the housing of engine oil pump (2).
Install bolts (7). Tighten the bolts to a torque of 22 N m (195 lb in).
Install the assembly of engine oil pump (2) to the cylinder block. Ensure that dowel (9) and dowel (10) are correctly aligned with the holes in the cylinder block.
Install bolts (1) to assembly of engine oil pump (2). Tighten the bolts to a torque of 22 N m (195 lb in).
Use Tooling (A) to check the backlash between idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
If suction pipe (5) had a support bracket, Follow Step 9.a through Step 9.e in order to install support bracket and the suction pipe.
Install a new gasket (3) (not shown) to suction pipe (5).
Install bolts (4) to suction pipe (1).
Position the assembly of suction pipe (5) onto oil pump (2). Tighten bolts (4) to a torque to 22 N m (195 lb in).
Position bracket (8) onto cylinder block and retaining clip. Install bolt (7) to the bracket. Install bolt (6) to the retaining clip. Hand tighten the bolts. Note: Ensure the correct location and orientation of the bracket and the retaining clip.
Tighten bolt (6) to a torque of 22 N m (195 lb in). Tighten bolt (7) to a torque of 44 N m (32 lb ft).Note: Ensure that the suction pipe and the bracket are not strained as the bolts are tightened.End By:
Install the engine oil pan. Refer to Disassembly