TIP 7J9552 - Caterpillar

7J9552 TIP Caterpillar parts 992

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA7J9552
7J-9552
7J9552

Weight: 32 pounds 14 kg.

Buy TIP 7J9552 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Threetrees 9W8552Rc 1U3552 Rc1U-3552Rc 7J9552 9J4552 1590550 Rock Bucket Teeth/Tooth J550

$195.99

23 May 2025

US: THREETREES

Threetrees 9W8552Rc 1U3552 Rc1U-3552Rc 7J9552 9J4552 1590550 Rock Bucket Teeth/Tooth J550
THREETREES 9W8552Rc 1U3552 Rc1U-3552Rc 7J9552 9J4552 1590550 Rock Bucket Teeth /Tooth J550

Threetrees 9W8552 1U3552 7J9552 1590559 9J4552 J550 Teeth, Tooth Fits Caterpillar

$137.19

23 Apr 2025

US: THREETREES

Threetrees 9W8552 1U3552 7J9552 1590559 9J4552 J550 Teeth, Tooth Fits Caterpillar
THREETREES 9W8552 1U3552 7J9552 1590559 9J4552 J550 Teeth, Tooth Fits Caterpillar

7J9552 - TIP Long HD 9W8552 1U3552 9J4552 fits Caterpillar (CAT)

$138.98

28 Dec 2023

US: Florida-Parts-Z

7J9552 - TIP Long HD 9W8552 1U3552 9J4552 fits Caterpillar (CAT)
FIRST PRICE PARTS

Show more prices Caterpillar parts

Number on catalog scheme: 5

For full view, you need register

Compatible equipment models: 7J9552:

WHEEL LOADER 992 Caterpillar

Information:

The following procedures are used in order to functionally check a Type VII governor. The housing cover plug and the seal for the throttle stop do not need to be removed. This check is intended as an aid to determine if a governor is functioning correctly. Use the following steps to check the governor.Note: The Type VII governor is similar to the Type VI governor.
Install the governor on the calibration bench. Refer to the Testing and Adjusting, "Installation Of Governor On 1U-7326 Governor Calibration Bench " section in this manual.Note: Do not install an oil supply to the Dual Horsepower mechanism. The oil supply is not needed to check the governor.
To check the High Horsepower, proceed with the checking procedure for the Type V governor. Refer to the Testing and Adjusting, "Governor (Type I, II, IV, and V) - Check" section in this manual.
To check the Low Horsepower setting, proceed with Step 4.
Illustration 1 g00660107
(1) Dual horsepower setscrew assembly
Remove the dual horsepower setscrew assembly (1). The dual horsepower setscrew assembly consists of the cover, a setscrew, a nut, and a setscrew plug.Note: If the governor is disassembled past this point, the governor may need to be reset.
Manually push in the old piston assembly in order to activate the low horsepower setting.Note: Push in the piston assembly until the piston bottoms out in order to engage the Low Horsepower setting.
Adjust the calibration bench to the "LOAD STOP ADJ" rpm that is specified in the TMI. Slowly move the throttle to the "LOW IDLE ADJ" position and back to the "THROT STOP ADJ" position. Do not move the throttle again during this checking procedure.
Check the governor output dimension. The governor output dimension should be within the "DUAL POWER STOP ADJ" dimension.
Reinstall dual horsepower setscrew assembly (1) .Note: The governor is operating correctly and the governor can be used again without any adjustment if the performance of the governor is acceptable according to the tolerance checks.Note: If the governor fails any of the High Horsepower tests, proceed to the Testing and Adjusting, "Governor (Type V) - Adjust" section in this manual.Note: If the governor fails only the Low Horsepower test, proceed to the Testing and Adjusting, "Governor (Type VII) - Adjust" section of this manual.