8T0831 TIP-LUBRICATOR Caterpillar parts
Rating:
Alternative (cross code) number:
CA8T0831
8T-0831
8T0831
CA8T0831
8T-0831
8T0831
Weight: 0.07 pounds 0 kg.
Information:
Outlet Relief Valve For Torque Converter
(4) Relief valve for converter outlet. (3) Body of relief valve for converter outlet. (23) Spacers.
Transmission Selector And Pressure Control Valve
(10) Speed selection spool. (11) Load piston. (13) Modulation relief valve. (14) Pressure differential valve. (16) Ratio valve for torque converter. (17) Direction selection spool. (24) Spacers.
Transmission Selector And Pressure Control Valve
(25) Setscrew. (26) Hole (No. 10-24 Threads). (X) Surface of valve body. Setscrew (25) must be installed in hole (26). Setscrew (25) permits correct operation of load piston (11). Setscrews must be assembled below surface (X). Transmission Oil Pump
Bench Test Specifications
Rotation is counterclockwise when seen from drive end.Type of pump: GearNumber of sections: OneFor test, use SAE 10W oil at 49°C (120°F)Output ... 97 liter/min (25.6 U.S. gpm) minimumAt a speed of ... 1800 rpmAt a pressure of ... 2550 kPa (370 psi)Transmission Control Linkage Adjustments
Accidental transmission engagement and sudden machine movement could cause personal injury. Transmission control linkage adjustment should be made only with the engine stopped.
Direction Control Linkage
(1) Rod end. (2) Bolt. (3) Nut. (4) Direction control cable assembly. (5) Speed selection control cable assembly. (6) Bulkhead nuts. (7) Bulkhead nuts. (A) 90 mm (3.5 in).Direction Linkage
1. Install rod end (1) on control cable so that one-half of the threads are engaged in the rod end.2. Loosen nuts (7) on the bulkhead. Move the transmission selector lever to neutral and push in the neutral lock.3. Tighten bulkhead nuts (7).4. Install nut (16), washer (15), seal (14) and bracket (9) past the threads on the transmission end of cable assembly (4).
Direction Control Linkage
(4) Direction control cable assembly. (8) Direction spool. (9) Bracket. (10) End. (11) Locknut. (12) Control cable. (13) Seal. (14) Seal. (15) Washer. (16) Nut.5. Install locknut (11) onto the end of control cable (12) and turn control cable (12) into end (10) until it bottoms in the threads. Apply 9S3263 Thread Lock on the threads of the control cable and tighten locknut (11).6. Move direction spool (8) to the neutral position and attach end (10) to the transmission direction spool.7. Turn bracket (9) on cable assembly (4) until the bracket face contacts the transmission face, then back off bracket (9) one-half turn. Disconnect end (10) from spool (8) and install seal (13) into the bracket, attach end (10) again to spool (8) and install bolts that hold bracket (9) to the transmission.8. Position seal (14), washer (15) and tighten nut (16) to lock cable assembly (4) in place.Speed Linkage
Speed Control Linkage
(5) Speed selection control cable assembly. (17) Bracket. (18) Bolt. (19) Yoke end. (20) Locknut. (21) Seal. (22) Speed selector spool. (23) Seal. (24) Control cable. (25) Washer. (26) Nut.1. Install rod end (1) on control cable so that one-half of the threads are engaged in the rod end.2. Loosen bulkhead nuts (6) on cable assembly (5). Position cable assembly (5) so the steering column bulkhead is in the middle of the threads. Tighten nuts (6).3. Turn bolt (2) to get dimension (A) of 90 mm (3.5 in).
Parts tip Caterpillar catalog:
8S8795
TIP
Caterpillar
Caterpillar
8M8289
TIP-PREWINDER
Caterpillar
Caterpillar
8J2210
TIP RIPPER
Caterpillar
Caterpillar
8E8503
TIP-RIPPER
Caterpillar
Caterpillar
8E8231
TIP-RIPPER
Caterpillar
Caterpillar
8E8230
TIP-RIPPER
Caterpillar
Caterpillar
9J0252
TIP SERVICE
Caterpillar
Caterpillar
9B4955
TIP-CAP JET
Caterpillar
Caterpillar
8W4171
TIP AR-POWER
Caterpillar
Caterpillar
8T5134
TIP
Caterpillar
Caterpillar
8T4504
TIP-SPRAY
Caterpillar
Caterpillar
8T3224
TIP G-NEEDLE
Caterpillar
Caterpillar