9N4252 TIP-LONG Caterpillar parts
307C, 308C, 311, 311B, 311C, 312, 312B, 312B L, 312C, 312C L, 312D, 314C, 345D L, 613C, 613C II, 938G II, 938H, IT38G II, M312, M313C, M313D, M315
Rating:
Alternative (cross code) number:
CA9N4252
9N-4252
9N4252
CA9N4252
9N-4252
9N4252
Weight: 8 pounds 3 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
All States Bucket Tooth fits Caterpillar 9N4252
All States Replaces Caterpillar Mfg Number(s) 9N4252 || Series: J Series || Sub Series: J250 Series || Pocket Height: 53 mm – 57 mm || Pocket Width: 66 mm – 70 mm
All States Replaces Caterpillar Mfg Number(s) 9N4252 || Series: J Series || Sub Series: J250 Series || Pocket Height: 53 mm – 57 mm || Pocket Width: 66 mm – 70 mm
Bucket Tooth fits Caterpillar 9N4252
Parts ASAP Replaces Caterpillar Mfg Number(s) 9N4252 || Series: J Series || Sub Series: J250 Series || Pocket Height: 53 mm – 57 mm || Pocket Width: 66 mm – 70 mm
Parts ASAP Replaces Caterpillar Mfg Number(s) 9N4252 || Series: J Series || Sub Series: J250 Series || Pocket Height: 53 mm – 57 mm || Pocket Width: 66 mm – 70 mm
Compatible equipment models: 9N4252:
Information:
If the engine is equipped with an air starting motor, use the following procedure:
Personal injury can result from removing hoses or fittings in a pressure system.Failure to relieve pressure can cause personal injury.Do not disconnect or remove hoses or fittings until all pressure in the system has been relieved.
Ensure that the air supply to the lubricator is OFF.
Illustration 1 g03789898
(1) Filler plug
(2) Bowl
(3) Drain valve
Slowly loosen filler plug (1) in order to release the pressure from the lubricator.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Place a suitable container under bowl (2) and open drain valve (3) in order to drain the oil from the bowl.
Remove bowl (2). Clean the bowl with warm water.
Dry the bowl. Inspect the bowl for cracks. If the bowl is cracked, replace the damaged bowl with a new bowl. Inspect the gasket. If the gasket is damaged, replace the gasket.
Install the bowl.
Make sure that drain valve (3) is closed.
For instructions on filling the lubricator, see this Operation and Maintenance Manual, "Air Starting Motor Lubricator Oil Level - Check" topic.
Personal injury can result from removing hoses or fittings in a pressure system.Failure to relieve pressure can cause personal injury.Do not disconnect or remove hoses or fittings until all pressure in the system has been relieved.
Ensure that the air supply to the lubricator is OFF.
Illustration 1 g03789898
(1) Filler plug
(2) Bowl
(3) Drain valve
Slowly loosen filler plug (1) in order to release the pressure from the lubricator.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Place a suitable container under bowl (2) and open drain valve (3) in order to drain the oil from the bowl.
Remove bowl (2). Clean the bowl with warm water.
Dry the bowl. Inspect the bowl for cracks. If the bowl is cracked, replace the damaged bowl with a new bowl. Inspect the gasket. If the gasket is damaged, replace the gasket.
Install the bowl.
Make sure that drain valve (3) is closed.
For instructions on filling the lubricator, see this Operation and Maintenance Manual, "Air Starting Motor Lubricator Oil Level - Check" topic.
Caterpillar SIS machinery equipment:
Caterpillar SIS
312 Excavator 6BL00001-UP (MACHINE) POWERED BY 3054 Engine »
9N-4252
TIP-LONG
312B & 312B L Excavators 2KW00001-UP (MACHINE) POWERED BY 3054 Engine »
9N-4252
TIP-LONG
312C & 312C L Excavators BNN00001-UP (MACHINE) POWERED BY 3054T Engine »
9N-4252
TIP-LONG
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine »
9N-4252
TIP-LONG
Caterpillar parts catalog:
Parts tip Caterpillar catalog:
9N4302
TIP-LONG
229, 235D, 311C, 312C L, 312D, 312D L, 313D, 313D2, 314C, 315C, 318B, 318C, 320 L, 320B, 320C, 321D LCR, 322B LN, 322C, 325, 325 L, 325 LN, 325B L, 330, 330B L, 330C, 615C, 950F, 950F II, 950G, 950G I...
229, 235D, 311C, 312C L, 312D, 312D L, 313D, 313D2, 314C, 315C, 318B, 318C, 320 L, 320B, 320C, 321D LCR, 322B LN, 322C, 325, 325 L, 325 LN, 325B L, 330, 330B L, 330C, 615C, 950F, 950F II, 950G, 950G I...
9J4309
TIP-PENETRATION
205, 206, 212, 215, 215B, 312D, 312D L, 315C, 318B, 318C, 320 L, 320B, 320C, 321D LCR, 322B LN, 322C, 325, 325B L, 330, 330 FM L, 950B, 950F, 950G, 950G II, 950H, 962G, 962G II, 962H, E140, E200B, M31...
205, 206, 212, 215, 215B, 312D, 312D L, 315C, 318B, 318C, 320 L, 320B, 320C, 321D LCR, 322B LN, 322C, 325, 325B L, 330, 330 FM L, 950B, 950F, 950G, 950G II, 950H, 962G, 962G II, 962H, E140, E200B, M31...
9W8309
TIP-PENETRATION
235B, 312D, 312D L, 315C, 320 L, 320B, 320C, 321D LCR, 322C, 325, 330, 330 FM L, E140, E200B, M312, M315, M318, M320
235B, 312D, 312D L, 315C, 320 L, 320B, 320C, 321D LCR, 322C, 325, 330, 330 FM L, E140, E200B, M312, M315, M318, M320
9N4253
TIP-ABRASION
311, 311B, 311C, 312B, 312C L, 312D, 314C, 613C, 613C II, M312, M315
311, 311B, 311C, 312B, 312C L, 312D, 314C, 613C, 613C II, M312, M315
9W8259
TIP-PENETRATION
307C, 308C, 311, 311B, 311C, 312B, 312C L, 312D, 314C, E110B, E120B, E200B, E240C, EL240B, M312, M315
307C, 308C, 311, 311B, 311C, 312B, 312C L, 312D, 314C, E110B, E120B, E200B, E240C, EL240B, M312, M315
1835300
TIP
311C, 312C L, 312D, 312D2, 312D2 L, 312E L, 313D2, 314E LCR, 315C, 317B LN, 318C, 320C, 322B L, 322C, 325C
311C, 312C L, 312D, 312D2, 312D2 L, 312E L, 313D2, 314E LCR, 315C, 317B LN, 318C, 320C, 322B L, 322C, 325C
1932750
TIP AS
311C, 312C L, 320C, 320C FM
311C, 312C L, 320C, 320C FM
2085254
TIP
311C, 312C L, 312D, 314C, 314E LCR, 315C
311C, 312C L, 312D, 314C, 314E LCR, 315C
9N4303
TIP-ABRASION
312D, 312D L, 314C, 315C, 320 L, 320B, 320C, 321D LCR, 322C, 325, 330, 330 FM L, M320
312D, 312D L, 314C, 315C, 320 L, 320B, 320C, 321D LCR, 322C, 325, 330, 330 FM L, M320
9W6559
TIP-PENETRATION
235, 245, 245D, 330, 330 L, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 350, 365B, 365B L, 375, 375 L, 385B
235, 245, 245D, 330, 330 L, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 350, 365B, 365B L, 375, 375 L, 385B
1073450
TIP-WIDE
235C, 322B L, 322C, 325B L, 325C, 330, 330B, 330B L, 330C L, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 350, 385B
235C, 322B L, 322C, 325B L, 325C, 330, 330B, 330B L, 330C L, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 350, 385B
2862117
TIP-GENERAL PURPOSE
324D, 324D L, 324D LN, 325D, 325D L, 329D L, 329D LN, 330D L, 330D LN, 336D L, 336D LN, 336E LH, 345C, 345C L, 345D L, 345D L VG, 349D L, 349E L, 349E L VG, 980H, 980K, 982M, 988K
324D, 324D L, 324D LN, 325D, 325D L, 329D L, 329D LN, 330D L, 330D LN, 336D L, 336D LN, 336E LH, 345C, 345C L, 345D L, 345D L VG, 349D L, 349E L, 349E L VG, 980H, 980K, 982M, 988K
8J9840
TIP GP-WIDE
235, 245, 245B, 245D, 345B, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 350, 365B, 365B L, 375, 375 L, 385B, 5110B
235, 245, 245B, 245D, 345B, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 350, 365B, 365B L, 375, 375 L, 385B, 5110B
2320078
TIP GP-ABRASION
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 993K, 994F
374D L, 385C, 385C FS, 385C L, 390D, 390D L, 992G, 992K, 993K, 994F
2209169
TIP GP-ABRASION
322C, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 330C, 330C L, 330D L, 330D LN, 345C, 345C L, 980H, 988G, 988H
322C, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 330C, 330C L, 330D L, 330D LN, 345C, 345C L, 980H, 988G, 988H
2297163
TIP GP-PENETRATION PLUS
349E L, 349E L VG, 365B, 365B L, 365C, 365C L, 374D L, 385B, 385C, 385C FS, 385C L, 390D, 390D L, 992K
349E L, 349E L VG, 365B, 365B L, 365C, 365C L, 374D L, 385B, 385C, 385C FS, 385C L, 390D, 390D L, 992K
1959182
TIP GP-PENETRATION PLUS
320C, 320D, 320D GC, 320D L, 320D2, 322C, 323D L, 323D2 L, 324D, 324D L, 325B L, 325C, 326D L, 329D, 329D L, 330C L
320C, 320D, 320D GC, 320D L, 320D2, 322C, 323D L, 323D2 L, 324D, 324D L, 325B L, 325C, 326D L, 329D, 329D L, 330C L
1959183
TIP GP-PENETRATION PLUS
323D L, 323D2 L, 324D, 325C, 325D, 326D L, 329D, 329D L, 330C, 330C L, 330D, 336D, 336D2, 340D L, 340D2 L, 345B II
323D L, 323D2 L, 324D, 325C, 325D, 326D L, 329D, 329D L, 330C, 330C L, 330D, 336D, 336D2, 340D L, 340D2 L, 345B II
4T5224
TIP GP
950B, 950B/950E, 950F, 950F II, 950G, 950G II, 960F, 962G, 962G II, 966D, 966F, 966F II, 966G, 966G II, 966H, 970F, 972G, 972G II, 972H, 973, 973C, 980C, 980F, 980F II
950B, 950B/950E, 950F, 950F II, 950G, 950G II, 960F, 962G, 962G II, 966D, 966F, 966F II, 966G, 966G II, 966H, 970F, 972G, 972G II, 972H, 973, 973C, 980C, 980F, 980F II
3A7237
TIP GP
943, 953, 953B
943, 953, 953B
3G3351
TIP GP
225, 225D, 229, 229D, 235, 235B, 235C, 235D, E300
225, 225D, 229, 229D, 235, 235B, 235C, 235D, E300
8J9842
TIP GP-LONG
235, 235B, 235C, 235D, 245, 245B, 245D, 330, 330 FM L, 330 L, 330B L, 330C L, 345B, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E, 350, 365B, 365B II, 365B L, 365C, 365C L, 375, 375 ...
235, 235B, 235C, 235D, 245, 245B, 245D, 330, 330 FM L, 330 L, 330B L, 330C L, 345B, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E, 350, 365B, 365B II, 365B L, 365C, 365C L, 375, 375 ...
9W8452
TIP-LONG
225, 229, 235, 235B, 235C, 235D, 322B L, 322B LN, 322C, 325, 325B L, 325C, 330, 330B, 330B L, 330C, 330C L, 330D L, 336D, 336E, 336E H, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 349E, 350, 98...
225, 229, 235, 235B, 235C, 235D, 322B L, 322B LN, 322C, 325, 325B L, 325C, 330, 330B, 330B L, 330C, 330C L, 330D L, 336D, 336E, 336E H, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 349E, 350, 98...