AVSPARE.COM
parts catalog

TIRE & RIM GP 3237404 - Caterpillar



3237404 TIRE & RIM GP Caterpillar parts TIRE
Rating:
21
Alternative (cross code) number:
CA3237404
323-7404
3237404
Caterpillar 3237404 TIRE & RIM GP

Buy TIRE & RIM GP 3237404 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 1
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     4C-6726     Valve Spring Compressor     1    Start By:
Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Remove the electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure is for the removal of the inlet valve springs and the exhaust valve springs without removing the cylinder head. This procedure can be performed on only one cylinder at a time. This will prevent the inlet valves and the exhaust valves from falling into the cylinder.
Rotate the crankshaft in order to bring the piston to the top center position in the cylinder.
Illustration 1 g01019733
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Place the bottom portion of Tooling (A) on the cylinder head. Install hold down bolt (1) .
Install the remainder of Tooling (A) .
Tighten the nut on Tooling (A) in order to compress the inlet valve springs and the exhaust valve springs.
Remove retainer locks (3) .
Remove Tooling (A) .
Remove valve rotators (4) .
Remove inner valve spring (5) and outer valve spring (6) from each valve (2) .
Remove the bases from the cylinder head.
Install the inlet valve springs and the exhaust valve springs before you rotate the crankshaft.Installation Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     4C-6726     Valve Spring Compressor     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Ensure that the piston is at the top center position in order to install the inlet valve springs and the exhaust valve springs.
Install the bases for the inlet valve springs and the exhaust valve springs.
Illustration 2 g01019733
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Install inner valve spring (5) and outer valve spring (6) on each valve (2) .
Install valve rotators (4) .
Install Tooling (A). Install hold down bolt (1) .
Tighten the nut on Tooling (A) in order to compress the inlet valve springs and the exhaust valve springs.
Install retainer locks (3) .
Remove Tooling (A) .End By:
Install the electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
TH414C Telehandler KEK00373-UP (MACHINE)


Parts tire Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.