TOOL GP-STUD TENSIONER 2075034 - Caterpillar

Illustration 10 g06331089
Pin assembly
(14) Pin Assembly
(15) Holes
(A) Dimension
Measure dimension (A) of pin assembly (14). Make a measurement at two holes (15) that were used for the depth measurements. Find and record the average of the two measurements.
Subtract dimension (A) of pin assembly (14) recorded in Step 9 from the value recorded in Step 6.
When the shim pack thickness is determined, as calculated in Step 10, evenly divide the shim pack in half.Note: A maximum bearing preload of 0.254 mm (0.010 inch) is acceptable for each side of the machine when finalizing the shim pack thickness.
Illustration 11 g06331080
(11) Spacers
(12) 9X-8268 Washer
(13) 8T-0281 Bolt
Working on the original side of the machine. Remove six bolts (13), six washers (12),and six spacers (11).
Illustration 12 g06331538
(8) 199-5810 Shim Pack
(14) Pin Assembly
Install half the thickness of shim pack (8) determined in Step 10 under pin assembly (14).
Illustration 13 g06331080
(11) Spacers
(12) 9X-8268 Washer
(13) 8T-0281 Bolt
Ensure the threads of six bolts (13) are free from oil and contaminants and apply Tooling (B) to the threads of six bolts (13).
Install six bolts (13), six washers (12), and six spacers (11). Tighten six bolts (13) to a torque of 240 40 N m (177 30 lb ft).
Use Tooling (A) and partially remove pin assembly (15) on the other side of the machine.
Repeat Steps 13 through 19.
Check that the front axle housing and differential assembly is centered in the front frame. If the front axle housing and differential assembly is not centered, remove some of the shims from under one pin. Add the shims to the shim pack under the other pin until the front axle housing and differential is centered.
Illustration 14 g06331535
Pin assembly
(1) 8T-5065 Locknut
(6) 9X-8399 Washer
(7) 559-4144 Pin
(9) 559-4143 Bushing
(10) 264-4453 Bolt
(13) 8T-0281 Bolt
(14) Pin Assembly
Remove locknut (1), two washers (6), and bolt (10) from pin assembly (14) on both sides of the machine.
Illustration 15 g06332050
(1) 8T-5065 Locknut
(2) 8T-4184 Bolt
(3) 8T-4223 Hard Washer
(4) 559-4146 Plate
(6) 9X-8399 Washer
(10) 264-4453 Bolt
(16) Hole
Install plate (4), bolt (10), two washers (6), locknut (1), bolt (2), and washer (3). Torque locknut (1) to 16 N m (12 lb ft).
Measure the distance from the outer face of plate (4) to pin (7) Measure through hole (16) and record the result.
Remove plate (4), bolt (10), two washers (6), locknut (1), bolt (2), and washer (3).
Measure the thickness of plate (4) and record the result.
Subtract the thickness of plate (4) determined in Step 23 from the measurement taken in Step 21.
Illustration 16 g06332041
(5) 563-6244 Shim Pack
(7) 559-4144 Pin
Install the thickness of shim pack (5) determined in Step 24.
Illustration 17 g06332039
(1) 8T-5065 Locknut
(2) 8T-4184 Bolt
(3) 8T-4223 Hard Washer
(4) 559-4146 Plate
(6) 9X-8399 Washer
(10) 264-4453 Bolt
Install plate (4), bolt (10), one washer (6), bolt (2), and washer (3).
Ensure the thread of bolt (10) is free from oil and contaminants and apply Tooling (B) to the thread of bolt (10).
Install nut (1) and one washer (6). Torque nut (1) to 900 100 N m (665 75 lb ft).
Repeat