AVSPARE.COM
parts catalog

TOOL GP 5087865 - Caterpillar



5087865 TOOL GP Caterpillar parts TOOL
Rating:
31
Alternative (cross code) number:
CA5087865
508-7865
5087865
Caterpillar 5087865 TOOL GP
Weight: 313 pounds 142 kg.

Buy TOOL GP 5087865 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01074624
Schematic of the Loader Auxiliary Valve Port A SolenoidThis diagnostic code is associated with the Loader Auxiliary Valve Port A Solenoid. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal. The possible causes of the diagnostic code are listed:
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2242 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the ON position.
Disconnect the wires from the back of the connector at the ECM.
At the machine harness connector for the solenoid, measure the voltage from contact 1 (wire E543-WH) to frame ground. At the machine harness connector for the solenoid, measure the voltage from contact 2 (wire X750-OR) to frame ground. Expected Result:The voltage is 0 VDC.Results:
OK - There are no shorts in the wires. Proceed to Test Step 2.
NOT OK - A voltage is present in the wires. There is a short in the machine harness or in the wires. The short is to a separate voltage source.Repair: Repair the machine harness or replace the machine harness. Ensure that the fix has corrected the problem.STOPTest Step 2. CHECK THE OPERATION OF THE ECM.The disconnect switch and the key start switch remain in the OFF position. The machine harness connectors for the solenoid and the ECM remain disconnected.
Use a wire removal tool in order to remove the energize wire for the solenoid from the machine harness connector for the ECM. Remove (wire 543-WH) and the socket at connector contact J1-51 from the machine harness connector.
Reconnect the machine harness connectors to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the active diagnostic code.Expected Result:The diagnostic code of a FMI 03 changes to a FMI 05.Results:
OK - The FMI 03 changes to a FMI 05. The FMI 05 was activated after the energize circuit for the solenoid was disconnected. The ECM has responded correctly to the condition of an open circuit in the solenoid circuit. Reconnect the disconnected wire. Wire (543-WH) connects to the ECM at connector contact J1-51. Proceed to Test Step 3.
NOT OK - The FMI 03


Parts tool Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.