TORQUE CONVERTER 1M5212 - Caterpillar

Remove the current display and mounting.
Remove the head liner and access panels behind the buddy seat.
Cut the wire ties securing the harness to the Cab.Rerouting Harness from Overhead to Console Mount
Illustration 3 g06176740
Harness from overhead to console mount
Reroute the display and camera harness from the over head position through the rear panel notch to the gear selector following the existing harness routes.
Install the 450-5307 Display Mounting Kit.
Remove the existing gear selection cover.
Bolt the 426-5346 Bracket As to the center console using four 166-3777 Screws and four 9x-8256 Washers.
Bolt the 261-3222 Display Mounting Gp to the 426-5346 Bracket As using four 166-3777 Screws and four 9x-8256 Washers.
Bolt the 433-4905 Bracket to the 261-3222 Display Mounting Gp using four 166-3777 Screws and four 9x-8256 Washers.
Bolt the 459-2220 Electronic Control Gp to the 433-4905 Bracket using four 6V-5683 Bolts and four 114-6658 Washers.
Connect the harness plugs for Ethernet, CDL, Power/CAN, and Video to the back of the display.
Secure the harness to the 433-4905 Bracket using a 7K-1181 Cable Strap.
Secure the harness back towards the rear of the cab following existing routes.
Reinstall the removed headliner and access panels to the rear of the machine.Console Mount Kit G407 450-5307 Display Mounting Kit
Illustration 4 g06024683
Console mount kit G407 450-5307 Display Mounting Kit
(1) 7K-1181 Cable Strap
(2) 261-3222 Display Mounting Gp
(3) 426-5346 Bracket As
(4) 433-4905 Bracket
(5) 433-4915 Cover
(6) 439-6917 Cover
(7) 444-7076 Bracket As
(8) 114-6658 Washer
(9) 166-3777 Screw
(10) 6V-5683 Bolt
(11) 9X-8256 WasherIn Cab Mounting
Illustration 5 g06176807
In cab mounting
Notes
Two main cab harness wiring sets currently exist.
Pre Serial Break (Without factory display Ethernet Wiring)
(S/N: SSP1-508)
(S/N: ERM1-214)
(S/N: LAJ1-315)
Post Serial Break (With factory display Ethernet Wiring)
(S/N: SSP509-UP) (until G407 cab harness change)
(S/N: ERM215-UP) (until G407 cab harness change)
(S/N: LAJ316-UP) (until G407 cab harness change)
Some pre-serial break cabs have no factory installed display harnesses if the Objection Detection system option was omitted during the initial build.
When installing MineStar Onboard Fleet or Proximity Awareness:
Pre-Serial Break Cabs with Object Detection without an Ethernet display harness installed will need either the MineStar retrofit display harness, reworked Ethernet extension harness (pinned correctly for the display type), or the customer radio display harness.
GEN II Harness - 362-9052 Monitor Harness As
GEN III Harness - 377-5555 Wiring Harness
GEN IV Harness - 450-9668 Power Harness As - Very bulky harness
Extension Harness - 440-5480 Wiring Harness - Must be reworked for display connection
Customer Radio Harness Kit - 519-5020 Wiring Kit or 519-3668 Radio Harness As (This kit is recommended as the most preferred by dealers)
When upgrading from a CMPD era machine to a G407 era machine, the following should be considered:
Display
Display Mounting
Harness Jumper
Camera HarnessNote: Reference M0065842 for display upgrade instructions and parts list.Reference
Console Mount – CMPD 426-5376 Monitor Display Gp
Illustration 6 g06176873
Console mount – CMPD 426-5376 Monitor Display Gp