1T1519 TORQUE CONVERTER GP Caterpillar parts
910, G910, IT12
Rating:
Alternative (cross code) number:
CA1T1519
1T-1519
1T1519
CA1T1519
1T-1519
1T1519
Weight: 78 pounds 35 kg.
COMPACT WHEEL LOADER, WHEEL LOADER,
Compatible equipment models: 1T1519:
Number on catalog scheme:
3
For full view, you need register
Information:
The Scroll Switch Does Not Scroll
This procedure is for the "SCROLL" switch that does not scroll parameter values in the Display Area. The "Does Not Scroll" condition is probably caused by an undesired open circuit. Also, the Main Display Module may cause the problem (unlikely condition).
Locate The Switch.
Turn the "ECS" switch to the OFF/RESET position.
Locate the "SCROLL" switch. If necessary, use the Electrical System Schematic to assist in locating the switch.
Check for loose terminal connections or corroded terminal connections to the switch.
Clean the corroded terminals and tighten the loose connections.
Check The Harness.
Disconnect the signal wire from the switch.
Turn the "ECS" switch to the COOLDOWN/STOP position.
Alternately, ground the signal wire and float the signal wire.Expected Result: The Display Area should scroll from one parameter value to the next parameter value.Results:
OK - The Display Area scrolls from one parameter value to the next parameter value. The circuit is operating correctly. The switch has a problem. Check the switch or replace the switch.
Not OK - The Display Area does not scroll from one parameter value to the next parameter value. The signal wire for the engine harness probably has an open circuit. Proceed to Step 3.
Check The Harness.
Turn the "ECS" switch to the OFF/RESET position.
Connect a jumper wire from the signal wire to the ground wire. If a ground wire is not near, connect the signal wire to battery ground.
On the Electrical System Schematic, trace the signal wire from the switch to the Main Display Module. The contact that is used for the signal connector at the Main Display Module is contact 23.
Disconnect the engine harness from the Main Display Module.
At the engine harness connector for the Main Display Module, measure the resistance between the signal contact and contact 2 (ground).Expected Result: The resistance should be less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The harness resistance is correct. The Main Display Module has a problem. Replace the Main Display Module. For more information on this subject, see Testing And Adjusting, "Module - Replace".
Not OK - The resistance should be greater than 5 ohms. The engine harness has a problem. There is an open circuit between ground and the signal wire in the engine harness. Repair the engine harness or replace the engine harness.The Scroll Switch Continually Scrolls
This procedure is for the "SCROLL" switch that continually scrolls parameter values in the Display Area. The "Continually Scrolls" condition is probably caused by a short to ground. Also, the Main Display Module may cause this problem (unlikely condition).
Locate The Switch.
Turn the "ECS" switch to the OFF/RESET position.
Locate the "SCROLL" switch. If necessary, use the Electrical System Schematic to assist in locating the switch.
Check for loose terminal connections or corroded terminal connections to the switch.
Clean corroded terminals and tighten loose connections.
Check The Harness.
Disconnect the signal wire from the "SCROLL" switch.
Turn the ECS to the COOLDOWN/STOP position.Expected Result: The Display Area should NOT scroll from one parameter value to the next parameter value.Results:
OK - The Display Area does NOT scroll from
This procedure is for the "SCROLL" switch that does not scroll parameter values in the Display Area. The "Does Not Scroll" condition is probably caused by an undesired open circuit. Also, the Main Display Module may cause the problem (unlikely condition).
Locate The Switch.
Turn the "ECS" switch to the OFF/RESET position.
Locate the "SCROLL" switch. If necessary, use the Electrical System Schematic to assist in locating the switch.
Check for loose terminal connections or corroded terminal connections to the switch.
Clean the corroded terminals and tighten the loose connections.
Check The Harness.
Disconnect the signal wire from the switch.
Turn the "ECS" switch to the COOLDOWN/STOP position.
Alternately, ground the signal wire and float the signal wire.Expected Result: The Display Area should scroll from one parameter value to the next parameter value.Results:
OK - The Display Area scrolls from one parameter value to the next parameter value. The circuit is operating correctly. The switch has a problem. Check the switch or replace the switch.
Not OK - The Display Area does not scroll from one parameter value to the next parameter value. The signal wire for the engine harness probably has an open circuit. Proceed to Step 3.
Check The Harness.
Turn the "ECS" switch to the OFF/RESET position.
Connect a jumper wire from the signal wire to the ground wire. If a ground wire is not near, connect the signal wire to battery ground.
On the Electrical System Schematic, trace the signal wire from the switch to the Main Display Module. The contact that is used for the signal connector at the Main Display Module is contact 23.
Disconnect the engine harness from the Main Display Module.
At the engine harness connector for the Main Display Module, measure the resistance between the signal contact and contact 2 (ground).Expected Result: The resistance should be less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The harness resistance is correct. The Main Display Module has a problem. Replace the Main Display Module. For more information on this subject, see Testing And Adjusting, "Module - Replace".
Not OK - The resistance should be greater than 5 ohms. The engine harness has a problem. There is an open circuit between ground and the signal wire in the engine harness. Repair the engine harness or replace the engine harness.The Scroll Switch Continually Scrolls
This procedure is for the "SCROLL" switch that continually scrolls parameter values in the Display Area. The "Continually Scrolls" condition is probably caused by a short to ground. Also, the Main Display Module may cause this problem (unlikely condition).
Locate The Switch.
Turn the "ECS" switch to the OFF/RESET position.
Locate the "SCROLL" switch. If necessary, use the Electrical System Schematic to assist in locating the switch.
Check for loose terminal connections or corroded terminal connections to the switch.
Clean corroded terminals and tighten loose connections.
Check The Harness.
Disconnect the signal wire from the "SCROLL" switch.
Turn the ECS to the COOLDOWN/STOP position.Expected Result: The Display Area should NOT scroll from one parameter value to the next parameter value.Results:
OK - The Display Area does NOT scroll from
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts torque Caterpillar catalog:
7N5716
TORQUE CONTROL GP
910, 931, 931B, 955L, D3, D3B
910, 931, 931B, 955L, D3, D3B
4W5063
TORQUE CONTROL GP
3204, 3306, 910, 916, 926, 926A, 931B, 931C, 931C II, 935B, 935C, 935C II, 943, 953, D3B, D3C, D3C II, D4B, D4C, D4C II, D4H, D4HTSK II, D5C, D7H, G910, G916, G926, IT12, IT18, IT18B, IT28, IT28B
3204, 3306, 910, 916, 926, 926A, 931B, 931C, 931C II, 935B, 935C, 935C II, 943, 953, D3B, D3C, D3C II, D4B, D4C, D4C II, D4H, D4HTSK II, D5C, D7H, G910, G916, G926, IT12, IT18, IT18B, IT28, IT28B
910, 931C II, D3, D3B, D3C, D3C II, G910, IT12
910, G910, IT12
910, G910, IT12
1T1015
TORQUE CONVERTER GP
983, 983B
983, 983B
768C, 769C
9P7115
TORQUE CONVERTER GP
D10N, D9L
D10N, D9L
7N7975
TORQUE CONTROL GP
D10N, D9L
D10N, D9L