AVSPARE.COM
parts catalog

TORQUE CONVERTER AR 3727954 - Caterpillar



3727954 TORQUE CONVERTER AR Caterpillar parts 797F TORQUE
Rating:
48
Alternative (cross code) number:
CA3727954
372-7954
3727954
Caterpillar 3727954 TORQUE CONVERTER AR

Buy TORQUE CONVERTER AR 3727954 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compatible equipment models: 3727954:

TRUCK  797F   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g06087808
Schematic for the CAN data link
Table 1
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Turn the keyswitch to the OFF position.
B. Inspect the connectors in the circuit for the CAN data link.
Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
D. Check all the wiring associated with the CAN data link for abrasions and pinch points.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: A damaged wire or damaged connector was not found.
Proceed to Test Step 2.
2. Check the Status of the Other Devices on the Suspect CAN Data Link
A.Establish communication between the electronic service tool and the ECM.
B. Use the electronic service tool to view the status of the other devices on the suspect CAN data link.
If necessary, refer to the Electrical Schematic for the application.
Other devices
Result: One or more of the devices on the suspect data link is not visible on the electronic service tool.
Repair: Thoroughly inspect the electrical connectors for the suspect devices
Refer to Troubleshooting, "Electrical Connectors - Inspect".
Check the power supply to the suspect devices.
If necessary, refer to Troubleshooting, "Electrical Power Supply - Test".
If the fault has been resolved, return the engine to service.
If the fault is still present, proceed to Test Step 3.
Result: All devices are visible on the electronic service tool.
Proceed to Test Step 3.
3. Check the Data Link Terminating Resistance
A. Disconnect the P1 connector from the ECM.
B. Measure the resistance between the P1:38 and P1:39.
Between 50 Ohms and 70 Ohms
Result: The resistance is less than 50 Ohms - there is a short circuit in the harness.
Repair: Repair the connectors or the harness and/or replace the connectors or the harness. Ensure that all the seals are correctly in place and ensure that the connectors are correctly connected.
Use the electronic service tool to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The resistance is greater than 150 Ohms.
Proceed to Test Step 4.
Result: The resistance is between 110 and 130 Ohms
The resistance is correct. The fault may be in the connection to other devices on the data link.
Proceed to Test Step 4.
4. Check the Data Link Wiring
A. Disconnect each of the connectors that connect other devices on the data link.
B. Use a multimeter to measure the resistance between P1:38 and each of the CAN+ pins on other devices on the CAN data link.
C. Use a multimeter to measure the resistance between P1:39 and each of the CAN- pins on other devices on the CAN data link.
Less than 2.0 Ohms
Result: At least one of the resistance measurements is greater than 2.0 Ohms - there is an open circuit or high resistance in the wiring.
Repair: Repair the connectors or the harness and/or replace the connectors or the harness.
Ensure that

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
797F Off-Highway Truck LTZ00001-UP (MACHINE) POWERED BY C175 Engine
797F Off-Highway Truck LAJ00001-UP (MACHINE) POWERED BY C175-20 Engine
797F XQ Off-Highway Truck WSP00001-UP (MACHINE) POWERED BY C175-20 Engine


Parts torque Caterpillar catalog:

1837434 TORQUE CONVERTER GP
814F, 814F II, 815F, 815F II, 816F, 816F II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.