3L2040 TORQUE CONVERTER FLUID CHARGING GROUP Caterpillar parts
D353C
Rating:
Alternative (cross code) number:
CA3L2040
3L-2040
3L2040
CA3L2040
3L-2040
3L2040
Weight: 0.30 pounds 0 kg.
INDUSTRIAL ENGINE,
Compatible equipment models: 3L2040:
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5F-4764 Prybar 1 Start By:
Remove the valve cover.
Remove the exhaust manifolds.
Remove the accumulator (fuel injection).
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not open the high pressure fuel system without allowing the fuel system to purge. After the engine has shut down, allow the fuel system to purge for ten minutes. This operating fuel system contains high pressure. Exposure to high pressure fuel can result in personal injury.
Note: Use appropriate caps and plugs on all fittings to prevent contamination.Note: Inspect all O-rings, seals, and gaskets for wear and damage. Replace if necessary.
Illustration 1 g06330221
Disconnect harness assembly (1) and position out of the way.
Remove bolt (2) and injector clamp (3).
Illustration 2 g06330225
Place an identification mark on electronic unit injector (4) for installation purposes. Each electronic unit injector must be reinstalled in the original location.
Use Tooling (A) to pry out electronic unit injector (4) by the retaining collar.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5F-4764 Prybar 1 Start By:
Remove the valve cover.
Remove the exhaust manifolds.
Remove the accumulator (fuel injection).
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not open the high pressure fuel system without allowing the fuel system to purge. After the engine has shut down, allow the fuel system to purge for ten minutes. This operating fuel system contains high pressure. Exposure to high pressure fuel can result in personal injury.
Note: Use appropriate caps and plugs on all fittings to prevent contamination.Note: Inspect all O-rings, seals, and gaskets for wear and damage. Replace if necessary.
Illustration 1 g06330221
Disconnect harness assembly (1) and position out of the way.
Remove bolt (2) and injector clamp (3).
Illustration 2 g06330225
Place an identification mark on electronic unit injector (4) for installation purposes. Each electronic unit injector must be reinstalled in the original location.
Use Tooling (A) to pry out electronic unit injector (4) by the retaining collar.
Caterpillar SIS machinery equipment:
Caterpillar SIS
D353 ENGINE 46B00001-00598 »
3L-2040
TORQUE CONVERTER FLUID CHARGING GROUP
D353 ENGINE 46B00599-00808 »
3L-2040
TORQUE CONVERTER FLUID CHARGING GROUP
D353 & G353 ENGINES 46B00809-01557 »
3L-2040
TORQUE CONVERTER FLUID CHARGING GROUP
D353 ENGINE 46B01558-UP »
3L-2040
TORQUE CONVERTER FLUID CHARGING GROUP
Parts torque Caterpillar catalog:
4L0584
TORQUE SPRING GROUP
D342, D342C
D342, D342C