TORQUE CONVERTER AS (NO SERVICE PARTS) 8E8623 - Caterpillar

8E8623 TORQUE CONVERTER AS (NO SERVICE PARTS) Caterpillar parts 446, 446B, RT100

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA8E8623
8E-8623
8E8623

Caterpillar 8E8623 TORQUE CONVERTER AS (NO SERVICE PARTS)

Weight: 30 pounds 13 kg.

Buy TORQUE CONVERTER AS (NO SERVICE PARTS) 8E8623 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER, TELEHANDLER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

HVACSTAR Torque Converter 8E8623 8E-8623 compatible with Caterpillar CAT Backhoe Loaders 466 466B Telehandler RT100 RT80

$980.00

25 Jul 2024

CN: HVACSTAR

HVACSTAR Torque Converter 8E8623 8E-8623 compatible with Caterpillar CAT Backhoe Loaders 466 466B Telehandler RT100 RT80
HVACSTAR Part Number: 8E8623 8E-8623 || 8E8623 8E-8623 Torque Converter || Compatible with Caterpillar CAT Backhoe Loaders 466 466B || Compatible with Caterpillar CAT Telehandler RT100 RT80 || If you have any questions, please feel free to contact us, we'll try our best to solve it for you.

HOLDWELL Torque Converter 8E8623 8E-8623 compatible with Caterpillar CAT Backhoe Loaders 466 466B Telehandler RT100 RT80

$980.00

12 Aug 2023

CN: HOLDWELL-US

HOLDWELL Torque Converter 8E8623 8E-8623 compatible with Caterpillar CAT Backhoe Loaders 466 466B Telehandler RT100 RT80
HOLDWELL Part Name: Torque Converter || Part Number: 8E8623 8E-8623 || Fit for Caterpillar CAT Backhoe Loader 446 446B || Fit for Caterpillar CAT Telehandler RT100 RT80 || It is a replacement, not the original one, but it can work well for you! If you have any questions about our products, please feel free to contact us.

This part in 9 request: Show. This information for suppliers only!

2023-05-03

2023-05-03

2023-05-03

2023-05-03

2023-04-04

2023-04-04

2022-07-08

2021-06-22

2019-09-21

For full view, you need register

Compatible equipment models: 8E8623:

BACKHOE LOADER 446 446B

TELEHANDLER RT100 Caterpillar

Information:

Illustration 1 g00941086
Schematic for the temperature sender (power train oil)This diagnostic code is recorded when the ECM reads the signal voltage of the temperature sender and the voltage is too high. The possible causes of this diagnostic code are listed here:
The sender has failed.
The return circuit of the sender is open in the machine harness.
The signal circuit in the machine harness is shorted to a source of positive voltage.
The signal circuit in the machine harness is open or the sender is disconnected.
The ECM has failed. This is unlikely. Test Step 1. CHECK THE CONTROL AND THE HARNESS.
Turn the disconnect switch and the key start switch to the ON position.
Disconnect the machine harness connector from the temperature sender.
At the machine harness connector for the sender, measure the voltage (DCV) between the signal contact 2 (wire 443-YL) and the return contact 1 (wire 201-BK). Expected Result:The voltage is between 4.5 and 8.0 DCV.Results:
OK - The voltage is between 4.5 and 8.0 DCV. The ECM and the harness are correct. Repair: Replace the sender.STOP
NOT OK - The voltage is not between 4.5 and 8.0 DCV. The ECM or the harness has failed. Proceed to Test Step 2.Test Step 2. CHECK THE RETURN CIRCUIT OF THE HARNESS.
The sender remains disconnected.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness connector from the ECM.
Measure the resistance of the return circuit between contact 1 (wire 201-BK) of the machine harness for the sender and contact 28 of the machine harness for the ECM. Expected Result:The resistance is less than 5.0 ohms. Results:
OK - The resistance is less than 5.0 ohms. The harness resistance is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5.0 ohms. The ground circuit in the harness has failed. There is an open circuit between the ground contact and frame ground. Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK FOR A SHORTED HARNESS
The sender and the ECM remain disconnected from the machine harness.
The disconnect switch and the key start switch remain in the OFF position.
At the machine harness connector for the ECM, measure the resistance between the signal contact 28 (wire 443-YL) and the +battery circuit at contact 1. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The ECM has failed.Repair: It is unlikely that an ECM has failed. Exit this procedure. Perform this CID 0826 FMI 03 procedure again. If the failure is not found, replace the ECM. Refer to the Testing and Adjusting, "Module - Replace". STOP
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. There is a short between the +battery circuit and the signal circuit in the machine harness. Repair: Repair the machine harness or replace the machine harness. STOP