TRACK GP 1061646 - Caterpillar

1061646 TRACK GP Caterpillar parts D5H, D6M, D6N

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1061646
106-1646
1061646

Weight: 3824 pounds 1734 kg.

Buy TRACK GP 1061646 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

PU Bushing 1-06-1646 Front Susp. Lower arm Tundra,Sequoia,Land Cruiser,Lx570,

$49.38

18 Dec 2019
1134.0 Grams
-: -

PU Bushing 1-06-1646 Front Susp. Lower arm Tundra,Sequoia,Land Cruiser,Lx570,
Manufactured from the best durable polyurethane-based elastomer which increase the service life of the parts, serving your car two-tree times longer than rubber analogues. Siberian Bushing spareparts were tested in the most severe road and weather conditions in the world - in Siberia. || Siberian Bushing uses only high quality polyurethane compounds. Unlike the cheaper and obsolete rubber replacement parts, our parts withstand widest range of operating temperatures, stay flexible and durable even under hard loads and in extreme driving conditions. || All mount sizes (inner sleeve I.D. etc.) match the original ones. If not specified, the default polyurethane hardness is 65 (Shore A) that is equivalent to original rubber material. This provides safe and comfort driving, meantime increasing the responsiveness of your car. || TUNDRA, SEQUOIA, LAND CRUISER, LX570, || Ozone, oil and solvents resistant. Wear-out, tear-off and cuts resistant.

Number on catalog scheme:

Caterpillar 1061646 Parts scheme TRACK GP

For full view, you need register

Compatible equipment models: 1061646:

TRACK-TYPE TRACTOR D5H D6M D6N Caterpillar

Information:

Probable Causes
Air Inlet or Exhaust System
Blockage of the air inlet and exhaust systemEngine Speed/Timing Sensors
Calibration of the engine speed/timing sensorsIntake Manifold Pressure Sensor
Intake manifold pressure sensor
"Fuel Position" and/or "FRC Fuel Limit"Electronic Control Module (ECM)
Flash fileFuel
Fuel qualityValve Lash Adjustment
Verify for the correct valve lash adjustmentRecommended Actions
Blockage of the Air Inlet and Exhaust System
Check the air inlet system for restrictions and for leaks.
Check for an air filter restriction.
Perform a visual inspection of the air inlet piping for restrictions and for leaks.
Ensure that the turbocharger is in good repair.
Check the exhaust system for restrictions. If equipped, verify that the air shutoffs are operating correctly.
Repair any leaks that were found. Remove any restrictions that were found. Replace any damaged components.Calibration of the Engine Speed/Timing Sensors
Check the calibration of the engine speed/timing sensors. Refer to Troubleshooting, "Timing - Calibrate".
Verify that the crankshaft and the camshaft drive gears are set with the proper orientation. Refer to the Disassembly and Assembly, "Gear Group (Front) - Remove" manual.Intake Manifold Pressure Sensor, "Fuel Position", and/or "FRC Fuel Limit"
Monitor the status of "Fuel Position" and "Rated Fuel Limit" while the engine is operating under full load. If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the ECM is providing the correct control. Otherwise, proceed to the next Step.
Verify that there are no active diagnostic codes for the intake manifold pressure sensor.
Monitor the status of "Intake Manifold Pressure" on Caterpillar Electronic Technician (ET). When the engine is not running, "Intake Manifold Pressure" should be 0 kPa (0 psi).Note: A problem with the "FRC Fuel Limit" will only cause black smoke during acceleration. A problem with the "FRC Fuel Limit" will not cause black smoke during steady state operation.Flash File
Verify that the correct flash file is installed in the ECM. Refer to Troubleshooting, "ECM Software - Install" for information. Then verify that the correct engine parameters are being used. Refer to Troubleshooting, "Configuration Parameters".Fuel Quality
Cold weather adversely affects the characteristics of the fuel. Refer to Operation and Maintenance Manual, "Characteristics of Diesel Fuel" for information on improving the characteristics of the fuel during cold weather operation.Verify for the Correct Valve Lash Adjustment
Check for the correct valve lash adjustment. Refer to Systems Operation/Testing and Adjusting for information on adjustment of the valves.