AVSPARE.COM
parts catalog

TRACK GP 1305641 - Caterpillar


1305641 TRACK GP Caterpillar parts D10R, D10T
Rating:
40
Alternative (cross code) number:
CA1305641
130-5641
1305641
Caterpillar 1305641 TRACK GP
Weight: 10380 pounds 4708 kg.

Buy TRACK GP 1305641 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 1305641:

TRACK-TYPE TRACTOR  D10R   D10T   Caterpillar
  For full view, you need register

Information:


Table 1
Diagnostic Trouble Codes    
J1939 Code    CDL Code    Code Description
(code descriptions may vary)    Comments    
3242-18     E1014 (2)     Low DPF #1 Intake Temperature     The Aftertreatment Regeneration Device (ARD) has ignited and the A5:E2 Aftertreatment Controller has detected Low DPF inlet temperature.
Active regeneration is immediately disabled. Engine power is derated. The code is logged. The code remains active until electrical power to the A5:E2 Aftertreatment Controller is cycled. The following conditions can cause this code:
The exhaust piping between the outlet of the ARD and the intake of the DPF is disconnected and/or the DPF Inlet Temperature sensor has failed.    
Illustration 1 g03756736
(1) Exhaust piping (2) ClampsComplete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps    Values    Results    
1. Inspect the Exhaust Piping
A. Carefully Inspect the exhaust piping between the outlet of the ARD and the intake of the DPF. Look for the following problems:
1. Missing piping, cracked piping, or disconnected piping
2. Broken clamps or missing clamps
   
Damaged or Missing Piping
   
Result: The piping is not damaged or missing.
Proceed to Test Step 2.
Result: The piping is damaged or missing.
Repair: Make the necessary repairs. Proceed to Test Step 2.
   
Illustration 2 g03756816
(3) DPF inlet temperature sensor and wiring
Table 3
Troubleshooting Test Steps     Values     Results    
2. Inspect the DPF Inlet Temperature Sensor and Wiring
A. Carefully inspect the DPF Inlet temperature sensor wiring for damage.
B. Carefully inspect the DPF Inlet temperature sensor for damage.
   
Damaged Wiring or Sensor
   
Result: The wiring and sensor are not damaged.
Proceed to Test Step 3.
Result: The wiring and sensor are damaged.
Repair: Make the necessary repairs. Proceed to Test Step 3.
   
3. Perform an ARD Ignition Test
A. Connect to Cat ET.
B. Select the Diagnostics tab.
C. Select the Diagnostic Tests tab.
D. Select the ARD Ignition Test tab.
The ARD Ignition Test cannot be performed if the DPF soot loading is above 80%. When the DPF soot loading is above 80%, the Manual DPF Regeneration must be performed using Cat ET.
   
Test
   
Result: The ARD Ignition Test was successful.
Return the engine to service.
Result: The ARD Ignition Test was not successful.
Repair: Replace the DPF Inlet Temperature sensor. Repeat the ARD Ignition Test.
If the ARD Ignition Test was successful, return the engine to service.
If the ARD Ignition test was not successful, troubleshoot the generated codes.
   


Parts track Caterpillar catalog:

1912720 TRACK GP
D6N LGP, D6N OEM
4465071 TRACK GP
311F LRR, 312E, 314E CR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.