TRACK ADJUSTER & RECOIL GP 1493572 - Caterpillar

1493572 TRACK ADJUSTER & RECOIL GP Caterpillar parts 323D L, 325D, 329D L, 345C L, OEMS

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1493572
149-3572
1493572

Caterpillar 1493572 TRACK ADJUSTER & RECOIL GP

Buy TRACK ADJUSTER & RECOIL GP 1493572 Caterpillar genuine, new aftermarket tractor parts with delivery
MOBILE HYD POWER UNIT, UNDERCARRIAGE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

3pcs Fisheye Lens TTGO Camera Module OV2640 2 Megapixel Adapter Support YUV RGB JPEG for T-Camera Plus ESP32-DOWDQ6 8MB SPRAM

$51.20

24 May 2021

IN: AVANI EXCHANGE

3pcs Fisheye Lens TTGO Camera Module OV2640 2 Megapixel Adapter Support YUV RGB JPEG for T-Camera Plus ESP32-DOWDQ6 8MB SPRAM
AVANI EXCHANGE Feature:Camera: OV2640Camera Resolution: 2MegapixelType: Fisheye lensArray SizeUXGA1600 x 1200Power SupplyCore1.2VDC + 5%Analog2.5 ~ 3.0VDCI/O1.7V to 3.3VPower RequirementsActive125 mW (for 15 fps UXGA YUV mode)140 mW (for 15 fps UXGA compressed mode) Standby600 micro. || TemperatureOperation-30C to 70CRangeStable Image0C to 50COutput Formats (8-bit) YUV(422/420)/YCbCr422 RGB565/555 8-bit compressed data 8-/10-bit Raw RGB dataLens Size1/4 Chief Ray Angle25 Nnon-linear. MaximumUXGA/SXGA15 fpsImageSVGA30 fpsTransfer RateCIF60 fps. || Sensitivity0.6 V/Lux-secS/N Ratio40 dBDynamic Range50 dBScan ModeProgressiveMaximum Exposure Interval1247 x tROWGamma CorrectionProgrammablePixel Size2.2 m x 2.2 m. || Dark Current15 mV/s at 60 CWell Capacity12 KeFixed Pattern Noise 1% of VPEAK-TO-PEAKImage Area3590m x 2684mPackage Dimensions5725m x 6285m. || Package includes:3 x Camera.

This part in 1 request: Show. This information for suppliers only!

#1513492 1493572

2025-03-20

Number on catalog scheme: 8

Caterpillar 1493572 Parts scheme TRACK ADJUSTER & RECOIL GP

For full view, you need register

Compatible equipment models: 1493572:

MOBILE HYD POWER UNIT 323D L 325D 329D L 345C L

UNDERCARRIAGE OEMS Caterpillar

Information:

& Install Connecting Rod Bearings
Start By:a. remove oil pump 1. Check each connecting rod cap for its location on the crankshaft. Each cap (1) must have a number which is the same as the number on the connecting rod. Do not mix bearings.2. Use Tool (A) to turn the crankshaft until two of the pistons are at bottom center.3. Remove connecting rod caps (2). Remove the lower bearing from the connecting rod caps.4. Push the connecting rods away from the crankshaft and remove the upper bearings from the connecting rods.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.5. Install the upper half of the rod bearings in the connecting rod.6. Install the lower half of the rod bearing in the connecting rod cap. Make sure Plastigage (4) is in position on the lower bearing. Be sure tab (3) on the back of the bearings fits in the groove of the caps and connecting rods. When connecting rod caps are installed, make sure the number on the side of the cap is next to, and respective with, the number on the side of the connecting rod. 7. Put clean engine oil on threads. Put caps (1) in position on the connecting rods and install the nuts. Tighten the nuts with the procedure that follows: a. Tighten each nut to a torque of 82 8 N m (60 6 lb ft). b. Put a mark across the nuts and bolts. Tighten the nuts an additional 120 5 degrees (1/3 of a turn).
Do not use an impact wrench to tighten the nuts the additional 120 degrees (1/3 of a turn).
8. Remove the cap and measure the Plastigage. The rod bearing clearance for new bearings must be 0.071 to 0.168 mm (.0028 to .0066 in). The maximum clearance for used bearings is 0.25 mm (.010 in).9. Put bearing cap (1) in position and tighten the bolts as in Step 7.10. Do Steps 1 through 9 for the other connecting rod bearings.End By:a. install oil pump