2609456 TRACK GP Caterpillar parts
330D, 330D L, 336D
Rating:
Alternative (cross code) number:
CA2609456
260-9456
2609456
CA2609456
260-9456
2609456
EXCAVATOR,
Information:
Illustration 1 g02854936
Label with the injector code
Illustration 2 g02132457
Sequence for recording the injector code
The electronic service tool is used to load the injector codes into the ECM.The injector codes must be loaded into the ECM if any of the following conditions occur:
An electronic unit injector is replaced.
The ECM is replaced.
Diagnostic code 630-2 or 268-2 is active.
Electronic unit injectors are exchanged between cylinders.Note: Diagnostic code 630-2 or 268-2 will also become active if the engine serial number, FLS or FTS are not entered into the ECM.If the ECM is replaced, the injector codes are normally transferred to the new ECM as part of the "Copy Configuration" procedure. If the "Copy Configuration" procedure fails, the injector codes must be loaded manually.Installing Injector CodesNote: The injector code is located on the electronic unit injector.
Record the injector code for each electronic unit injector.
Connect the electronic service tool to the diagnostic connector. Refer to Troubleshooting, "Electronic Service Tools".
Turn the keyswitch to the ON position.
Select the following menu options on the electronic service tool:
Service
Calibrations
Injector Trim Calibration
Select the appropriate cylinder.
Click on the "Change" button.
Input the applicable injector code that was recorded in Test Step 1.
Click on the "OK" button. The injector code is loaded into the ECM.
Repeat the procedure for each cylinder, as required. Exchanging Electronic Unit InjectorsExchanging electronic unit injectors can help determine if a combustion problem is in the electronic unit injector or in the cylinder. If two electronic unit injectors that are currently installed in the engine are exchanged between cylinders, the injector codes must also be exchanged. Press the "Exchange" button at the bottom of the "Injector Trim Calibration" screen on the electronic service tool. Select the two electronic unit injectors that will be exchanged and press the "OK" button. The tattletale for the electronic unit injectors that were exchanged will increase by one.
Caterpillar SIS machinery equipment:
Caterpillar SIS
330D & 330D L Excavators EDX00001-UP (MACHINE) POWERED BY C9 Engine »
260-9456
TRACK GP
330D & 330D L Excavators EAH00001-UP (MACHINE) POWERED BY C9 Engine »
260-9456
TRACK GP
336D & 336D L Excavators KKT00001-UP (MACHINE) POWERED BY C9 Engine »
260-9456
TRACK GP
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine »
260-9456
TRACK GP
336D & 336D L Excavators PGW00001-UP (MACHINE) POWERED BY C9 Engine »
260-9456
TRACK GP
Parts track Caterpillar catalog:
2153087
TRACK GP
328D LCR, 330C FM, 330D L, 336D L
328D LCR, 330C FM, 330D L, 336D L
2648494
TRACK AR
330D L, 336D L
330D L, 336D L
2609446
TRACK GP
328D LCR, 330D L, 336D, 336D L
328D LCR, 330D L, 336D, 336D L
2609453
TRACK GP
330D L, 336D
330D L, 336D
2648495
TRACK GP
330D L, 330D LN, 330D MH, 336D L, 336D LN
330D L, 330D LN, 330D MH, 336D L, 336D LN
3472344
TRACK GP
330D MH, 336D, 336D L, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L
330D MH, 336D, 336D L, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L
3499554
TRACK AR
336D
336D
3636261
TRACK AR
336D
336D
3702931
TRACK AR
336D
336D
4257870
TRACK AR
336D
336D
4257871
TRACK AR
336D
336D
4257873
TRACK AR
336D
336D
1774971
TRACK GP
345B L
345B L
2639254
TRACK GP
303.5C, 303.5D, 303C CR
303.5C, 303.5D, 303C CR
9W9872
TRACK GP
973
973
8E9120
TRACK GP
D5E
D5E
3951044
TRACK GP
D11T
D11T
3997401
TRACK AR
D11T
D11T
2404013
TRACK AR
324D
324D
3408198
TRACK AR
311F LRR, 312E, 314E CR
311F LRR, 312E, 314E CR
3577499
TRACK AR
374F L
374F L