6T1305 TRACK GROUP-610MM (24 IN.) GROUSER SHOE Caterpillar parts
D9L
Rating:
Alternative (cross code) number:
CA6T1305
6T-1305
6T1305
CA6T1305
6T-1305
6T1305
Weight: 8014 pounds 3635 kg.
TRACK-TYPE TRACTOR,
This part in 2 request:
Show.
This information for suppliers only!
2021-05-25
2021-05-21
Compatible equipment models: 6T1305:
For full view, you need register
Caterpillar parts catalog:
Information:
Location of the Weld Link and Cable Strap to Improve Sensor Life
Note: The effectivity of the weld link for the D6R Series III is for the following tractors: (S/N: MRT1-466; GJB1-799; WRG1-702; WCB1-223; HDC1-251; HCD1-167; HKE1-244)An additional link and a cable strap should be added to D6R machines in order to provide the proper strain relief at the connector.Note: The link will only be applicable to the D6R.Location of the Weld Link on the D6R.
The following illustrations provide the location for the link on the D6R.
Illustration 1 g01407230
(1) The link is located on the rear, right hand side of the case frame next to the ROPS support.
Illustration 2 g01407231
(A) Location of the link 15 mm (0.60 inch) from the edge (B) Location of the link 40 mm (1.575 inch) to the center of the linkLocation of the Cable Straps for Improved Strain Relief of the Wire Leads that are attached to the Temperature Sensor
Acceptable Location of the Cable Strap for Improved Life of the Temperature Sensor
The following illustrations represent the proper placement of cable straps and the proper routing of the wire leads in order to provide proper strain relief.
Illustration 3 g01414275
The extra length of the harness has been tied down. The connector is also tied down at the harness clip.Note: The wiring harness is not pulled too tightly. This view is at the back of the sensor.
Illustration 4 g01414276
The sensor's pigtail is grouped properly. No portion of the harness is untied. The wires are not pulled tightly at the sensor.Unacceptable Strain Relief
The following illustrations show poor methods of strain relief.
Illustration 5 g01414278
The wires at the base of the sensor have been pulled too tightly. This will allow moisture to penetrate the seal. The moisture will also deteriorate the sensor.
Illustration 6 g01414280
The extra length from the bundle has not been tied down at the harness clip. Illustration 3 shows the proper restraint of the harness.
Note: The effectivity of the weld link for the D6R Series III is for the following tractors: (S/N: MRT1-466; GJB1-799; WRG1-702; WCB1-223; HDC1-251; HCD1-167; HKE1-244)An additional link and a cable strap should be added to D6R machines in order to provide the proper strain relief at the connector.Note: The link will only be applicable to the D6R.Location of the Weld Link on the D6R.
The following illustrations provide the location for the link on the D6R.
Illustration 1 g01407230
(1) The link is located on the rear, right hand side of the case frame next to the ROPS support.
Illustration 2 g01407231
(A) Location of the link 15 mm (0.60 inch) from the edge (B) Location of the link 40 mm (1.575 inch) to the center of the linkLocation of the Cable Straps for Improved Strain Relief of the Wire Leads that are attached to the Temperature Sensor
Acceptable Location of the Cable Strap for Improved Life of the Temperature Sensor
The following illustrations represent the proper placement of cable straps and the proper routing of the wire leads in order to provide proper strain relief.
Illustration 3 g01414275
The extra length of the harness has been tied down. The connector is also tied down at the harness clip.Note: The wiring harness is not pulled too tightly. This view is at the back of the sensor.
Illustration 4 g01414276
The sensor's pigtail is grouped properly. No portion of the harness is untied. The wires are not pulled tightly at the sensor.Unacceptable Strain Relief
The following illustrations show poor methods of strain relief.
Illustration 5 g01414278
The wires at the base of the sensor have been pulled too tightly. This will allow moisture to penetrate the seal. The moisture will also deteriorate the sensor.
Illustration 6 g01414280
The extra length from the bundle has not been tied down at the harness clip. Illustration 3 shows the proper restraint of the harness.
Parts track Caterpillar catalog:
3879486
TRACK
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C