AVSPARE.COM
parts catalog

TRANSFORMER AS 2152434 - Caterpillar


2152434 TRANSFORMER AS Caterpillar parts G3406, G3408, G3408B, G3412
Rating:
14
Alternative (cross code) number:
CA2152434
215-2434
2152434
Caterpillar 2152434 TRANSFORMER AS
Weight: 1 pounds 0 kg.

Buy TRANSFORMER AS 2152434 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: 2152434:

GAS ENGINE  G3406   G3408   G3408B   G3412   Caterpillar
Number on catalog scheme: 7
  For full view, you need register

Information:


Illustration 27 g03319772
Remove the link box section.Note: If necessary, use the small hydraulic press to spread the track links.
Illustration 28 g03319781
Install new track seals into the counter bores of the master track links.
Illustration 29 g03319796
Position the slip fit master joint section.Note: If necessary, use the small press to spread the track links.
Illustration 30 g03319806
Use 100 ton track press to install track pin. Check for proper pin protrusion. Refer to (X) in Illustration 16 and Table 8.Note: Do not apply grease to the track pin or inside the adjoining slip fit master track bushing. During assembly, the grease applied will be captured between the track pin and the pin bore of the standard links. The captured grease will contribute to pin walking in the future.
Illustration 31 g03319817
Install the track seals into the counter bore of the track links.
Illustration 32 g03319824
Align the ends of the link assembly.
Lubricate the master pin with grease.Note: Grease should be used for this installation of the slip fit master pin. The master pin cannot walk inside the track links pin ends due to the design of the pin.
Use a hammer to install the master pin.
Illustration 33 g03319840
Install the cotter pin in to the master pin.
Illustration 34 g03748015
All paint, loose rust, metal debris, and dirt must be removed from the mating surfaces of the track components.The paint on the mating surfaces of new track links must be removed before installation of the track shoes. The correct clamping force cannot be achieved if all the paint is not removed. The following methods may be used to remove the paint:
Use a 24-grit sandpaper to remove the paint from the mating surfaces of the track links and the track shoes. A light mist of water should be sprayed on the mating surface during the sanding. The water will help keep the sandpaper clean during sanding.
A paint remover may be used to remove the paint from the mating surfaces of the track links and the track shoes. Make sure that the paint remover does not contact the track seal. The paint remover can damage the track seal.
Do not use a torch to remove the paint from the mating surfaces of the track links and the master track links. The high temperatures can damage the track seals.Note: The track bolt and threads of the track nuts must be in good condition.
Lubricate the threads of the track bolts and lubricate the mating surface of the bolt head with Loctite® C5-A® Copper Based Anti-Seize Compound.
Align the holes in the track shoes with the holes in the track links.Note: The threads of the bolts will be damaged if the holes are not aligned.
Place a track bolt in each hole and start the nut by hand.
Illustration 35 g03319441
Follow the correct pattern in Illustration 35 to torque the bolts.
Table 10
Torque Specifications
Model Bolt Size Preliminary Torque Additional Turn
320
321
322
323
324
325
326
329 M20 X 1.5 400.0 70.0 N m (295.024 51.63 lb ft) 120° 5°
328
330
336
MD6290 M22 X 1.5 700 70 N m (516.29 51.63 lb ft) 120° 5°
Illustration 36 g03748022
Perform an additional 120°

Caterpillar parts catalog:

Caterpillar parts catalog
G3408 Engine 6NB00001-UP
G3412 Engine 7DB00001-UP
G3406 Industrial Engine Natural Gas 4FD00001-UP
G3406 Engine 1RK00001-UP
G3408 Low Emission Engine 6RJ00001-UP


Parts transformer Caterpillar catalog:

1226588 TRANSFORMER AS-CURRENT
3306, 3306B, 3406C, 3408, 3412C, 3456, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C15, C175-16, C18, C27, C32, G3304, G3306, G3406, G3408, G3408B, G3408C, G3412, G3508, G3512, G3512E,...
9Y9437 TRANSFORMER AS
3114, 3116, 3208, 3306, 3306B, 3406B, 3406C, 3408C, 3412C, C15, C18, G3306, G3306B, G3406
4P8698 TRANSFORMER
3406B, 3406C, G3406
9Y3861 TRANSFORMER
3406B, 3406C, 3408, 3412, 3412C, G3406, G3408, G3408B, G3412, SR4
4P7798 TRANSFORMER
3408, 3408C, G3408, G3408B
4P4477 TRANSFORMER AS
3412, 3412C, 3508, 3512, 3516, 3516B, C15, C18, G3408, G3412, G3512, G3516, PM3412, SR4, SR4B
7E5464 TRANSFORMER
3412, 3412C, 3508, 3512, 3512B, 3512C, 3516, 3516B, C15, C18, G3408, G3412, G3512E, G3516, G3516B, G3516C, G3516E, PM3412, SR4, SR4B
3N1964 TRANSFORMER ASSEM.
3208, 3304, 3306, 3406, 3406B, 3408, 3412, 3412C, 3508, 3512, 3516, D343, D346, D348, D379B, D398B, D399, G3306, G3408, G3412, G343, G3508, G3512, G3516, G398, G399, SR4
2W3747 TRANSFORMER AS
G3304, G3304B, G3306, G3306B, G3406, G3408, G3412, G342C, G379, G398, G399
4W5439 TRANSFORMER AS
G3406, G3408, G3408B, G3412, G398, G399
9Y4167 TRANSFORMER AS
G3406, G3408, G3408B, G3412
9Y4167 TRANSFORMER AS
G3406, G3408, G3408B, G3412
1072400 TRANSFORMER AS
G3304, G3304B, G3306, G3306B
1288088 TRANSFORMER
G3408, G3412, G3512, G3516
7W4377 TRANSFORMER
G3508, G3512, G3516, G3606, G3606B, G3608, G3612, G3616
6I4452 TRANSFORMER AS
G3508, G3512, G3516
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.