3649700 TRANSMISSION AR Caterpillar parts
966M XE, 972M XE
Rating:
Alternative (cross code) number:
CA3649700
364-9700
3649700
CA3649700
364-9700
3649700
Weight: 1906 pounds 864 kg.
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
SPARTA Flo-Pac Scrub Brush Cleaning Brush, Wash Brush with Dual Surface Brush for Cleaning, 10 Inches, Black, (Pack of 12)
SPARTA Cleaning brush has an angled design for cleaning multiple surfaces and attaches to a Carlisle Flow-Thru handle (sold separately), which delivers a constant stream of water to the brush to wash away dirt and debris from vehicle exteriors || Durable plastic foam block has an NPTF-threaded insert for use with handle || Block has five holes for even water distribution || Polystyrene bristles offer good chemical resistance, shape recovery, and extended life, and are flagged for catching fine dust and debris || Measures 10 x 4-1/2 inches overall (L x W)
SPARTA Cleaning brush has an angled design for cleaning multiple surfaces and attaches to a Carlisle Flow-Thru handle (sold separately), which delivers a constant stream of water to the brush to wash away dirt and debris from vehicle exteriors || Durable plastic foam block has an NPTF-threaded insert for use with handle || Block has five holes for even water distribution || Polystyrene bristles offer good chemical resistance, shape recovery, and extended life, and are flagged for catching fine dust and debris || Measures 10 x 4-1/2 inches overall (L x W)
SPARTA Flo-Pac Scrub Brush Cleaning Brush, Wash Brush with Dual Surface Brush for Cleaning, 10 Inches, Black, (Pack of 12)
SPARTA Cleaning brush has an angled design for cleaning multiple surfaces and attaches to a Carlisle Flow-Thru handle (sold separately), which delivers a constant stream of water to the brush to wash away dirt and debris from vehicle exteriors || Durable plastic foam block has an NPTF-threaded insert for use with handle || Block has five holes for even water distribution || Polystyrene bristles offer good chemical resistance, shape recovery, and extended life, and are flagged for catching fine dust and debris || Measures 10 x 4-1/2 inches overall (L x W)
SPARTA Cleaning brush has an angled design for cleaning multiple surfaces and attaches to a Carlisle Flow-Thru handle (sold separately), which delivers a constant stream of water to the brush to wash away dirt and debris from vehicle exteriors || Durable plastic foam block has an NPTF-threaded insert for use with handle || Block has five holes for even water distribution || Polystyrene bristles offer good chemical resistance, shape recovery, and extended life, and are flagged for catching fine dust and debris || Measures 10 x 4-1/2 inches overall (L x W)
This part in 2 request:
Show.
This information for suppliers only!
2024-05-16
2022-02-21
For full view, you need register
Information:
During the installation of a PL522 or 523 system, the wiring harness is connected to the existing Cat Data Link wiring on the machine. If the installation is not done properly, the continuity of the Cat Data Link wiring may be open intermittently. This condition may not be apparent immediately. Improper installation will cause a problem when you are trying to connect the Caterpillar Electronic Technician (Cat ET) service tool to the machine.
Cat ET may report that no ECM has been found.
Cat ET may not report every ECM that is on the machine.
Cat ET may report an ECM but the ECM will not have any data.If the Cat Data Link wires for the PL522 or 523 are reversed, the ECM will not appear after connecting Cat ET.Test Step 1. VERIFY THAT THE CAT DATA LINK WIRES ARE NOT REVERSED.
Check that the positive CAT Data Link wire (893-GN(Green)) in the wiring harness for the Product Link is connected to the positive CAT Data Link wire (893-GN(Green) or 944-OR(Orange)) of the wire harness for the machine.
Check that the negative CAT Data Link wire (892-BR(Brown)) in the wiring harness for the Product Link is connected to the negative CAT Data Link wire (892-BR(Brown) or 945-BR(Brown)) of the wire harness for the machine. Expected Result:The CAT Data Link wires are properly connected.Results:
OK - The wires for the CAT Data Link are properly connected. Proceed to Test Step 2.
NOT OK - The wires for the CAT Data Link are reversed.Repair: Reinstall the CAT Data Link wires correctly and check the operation of the Product Link module by using Cat ET .STOPTest Step 2. CHECK THE WIRING WITH A MULTIMETER.
Turn off the machine and turn the disconnect switch to the OPEN position.
Measure the resistance of the negative CAT Data Link wire from the service connector (contact "E") to the location for the spliced CAT Data Link wire. Note the resistance.
Measure the resistance of the positive CAT Data Link wire from the service connector (contact "D") to the location for the spliced CAT Data Link wire. Note the resistance. Expected Result:The resistance in both wires is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. Repair: Repair the wiring harness. After repairing, resume the Product Link installation setup procedures.STOPTest Step 3. VERIFY THAT THE WIRING FOR THE CAT DATA LINK IS PROPERLY CONNECTED.
Check the spliced connections for the CAT Data Link that were made during the installation. Verify that all connections are clean and tight.
Reconnect the harness connectors that were disturbed during the installation. Ensure that all of the pins are correctly seated in the sockets.
Reconnect the cable from the service tool connector. Attempt to access the Cat Data Link by using Cat ET . Expected Result:Cat ET lists the ECM systems that are
Cat ET may report that no ECM has been found.
Cat ET may not report every ECM that is on the machine.
Cat ET may report an ECM but the ECM will not have any data.If the Cat Data Link wires for the PL522 or 523 are reversed, the ECM will not appear after connecting Cat ET.Test Step 1. VERIFY THAT THE CAT DATA LINK WIRES ARE NOT REVERSED.
Check that the positive CAT Data Link wire (893-GN(Green)) in the wiring harness for the Product Link is connected to the positive CAT Data Link wire (893-GN(Green) or 944-OR(Orange)) of the wire harness for the machine.
Check that the negative CAT Data Link wire (892-BR(Brown)) in the wiring harness for the Product Link is connected to the negative CAT Data Link wire (892-BR(Brown) or 945-BR(Brown)) of the wire harness for the machine. Expected Result:The CAT Data Link wires are properly connected.Results:
OK - The wires for the CAT Data Link are properly connected. Proceed to Test Step 2.
NOT OK - The wires for the CAT Data Link are reversed.Repair: Reinstall the CAT Data Link wires correctly and check the operation of the Product Link module by using Cat ET .STOPTest Step 2. CHECK THE WIRING WITH A MULTIMETER.
Turn off the machine and turn the disconnect switch to the OPEN position.
Measure the resistance of the negative CAT Data Link wire from the service connector (contact "E") to the location for the spliced CAT Data Link wire. Note the resistance.
Measure the resistance of the positive CAT Data Link wire from the service connector (contact "D") to the location for the spliced CAT Data Link wire. Note the resistance. Expected Result:The resistance in both wires is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. Repair: Repair the wiring harness. After repairing, resume the Product Link installation setup procedures.STOPTest Step 3. VERIFY THAT THE WIRING FOR THE CAT DATA LINK IS PROPERLY CONNECTED.
Check the spliced connections for the CAT Data Link that were made during the installation. Verify that all connections are clean and tight.
Reconnect the harness connectors that were disturbed during the installation. Ensure that all of the pins are correctly seated in the sockets.
Reconnect the cable from the service tool connector. Attempt to access the Cat Data Link by using Cat ET . Expected Result:Cat ET lists the ECM systems that are
Caterpillar SIS machinery equipment:
Caterpillar SIS
966M XE Wheel Loader B8P00001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
972M XE Wheel Loader M5S00001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
966M XE Wheel Loader FL200001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
972M XE Wheel Loader L9S00001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
966M XE Wheel Loader XCR00001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
972M XE Wheel Loader AN300001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
966M XE Wheel Loader DZL00001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
972M XE Wheel Loader R1Z00001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
966M XE Wheel Loader P6C00001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
972M XE Wheel Loader EDW00001-UP (MACHINE) POWERED BY C9.3 Engine »
364-9700
TRANSMISSION AR
Caterpillar parts catalog:
Parts transmission Caterpillar catalog:
3859291
TRANSMISSION AR
844K, 990K
844K, 990K
3941136
TRANSMISSION AR
824K, 825K
824K, 825K
4214449
TRANSMISSION AR
950 GC
950 GC
3954645
TRANSMISSION GP
MH3037
MH3037
3633035
TRANSMISSION AR
TH337C
TH337C
3161940
TRANSMISSION AR
TH337C
TH337C