AVSPARE.COM
parts catalog

TUBE 0005255 - Caterpillar



0005255 TUBE Caterpillar parts TUBE
Rating:
86
Alternative (cross code) number:
CA0005255
000-5255
0005255
Caterpillar 0005255 TUBE
Weight: 45 pounds 20 kg.

Buy TUBE 0005255 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Refer to Testing and Adjusting, "Tooling Preparation" for additional information for tooling assembly and for alternate methods of testing.
Illustration 1 g01018165
Turn screws (2) counterclockwise and remove panel (1) .
Illustration 2 g00796016
Connect the communication adapter to service tool connector (3) .High Idle Adjustment
Ensure that the engine start switch key is in the OFF position.
Move the governor control lever to the HIGH IDLE position.
Exit the machine.
Illustration 3 g01018357
Remove three bolts (1) and washers.
Remove access panel (2) .
Illustration 4 g01020206
Remove the cotter pin from pin (6) .
Remove pin (6) from clevis (4) .
Loosen jam nut (7) .
Move governor lever (5) against HIGH IDLE stop (3) .Note: Maintain this position for the rest of this procedure.
Adjust clevis (4) so that the clevis is properly aligned with governor lever (5) .
Install pin (6) and install a new cotter pin.
Tighten jam nut (7) .
Verify that the cable is adjusted properly for HIGH IDLE.
Ensure that the laptop computer is connected to the data port. Refer to "Preparations for Checking Engine Speed".
Enter the machine.
Fasten the seat belt.
Start the engine and increase the engine speed to HIGH IDLE.
Note the engine speed. The engine speed should be 2400 40 rpm. If the engine speed is not within the specification, repeat Step 1 through Step 8.
Decrease engine speed to LOW IDLE and stop the engine.
Exit the machine.
If the engine speed at LOW IDLE is correct, install the engine access panel.Low Idle Adjustment
Ensure that the engine start switch key is in the OFF position.
Move the governor control lever to the HIGH IDLE position.
Exit the machine.
Illustration 5 g01018357
Remove three bolts (1) and washers.
Remove access panel (2) .
Illustration 6 g01020560
Slowly move the governor control lever until governor lever (3) contacts the LOW IDLE stop (4) .
Illustration 7 g01020563
Remove four bolts (5) and washers.
Remove plate (6) .
Illustration 8 g01020562
Ensure that surface (A) of pedal assembly (9) contacts the bottom of stop bolt (7). If necessary, adjust the stop bolt.
Loosen jam nut (8) .
Turn stop bolt (7) until the bottom of stop bolt (7) contacts surface (A) .
Tighten jam nut (8) .
Verify that the stop bolt for LOW IDLE is adjusted properly.
Ensure that the laptop computer is connected to the data port. Refer to "Preparations for Checking Engine Speed".
Enter the machine.
Fasten the seat belt.
Start the engine and increase the engine speed to HIGH IDLE.
Fully depress the deceleration pedal.
Note the engine speed. The engine speed should be 850 50 rpm. If the engine speed is not within the specification, repeat Step 1 through Step 10.
Decrease engine speed to LOW IDLE and stop the engine.
Exit the machine.
Install the engine access panel and install the plate.


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.