0550153 TUBE A-BASIC Caterpillar parts
Rating:
Alternative (cross code) number:
CA0550153
055-0153
0550153
CA0550153
055-0153
0550153
Weight: 0.17 pounds 0 kg.
Information:
1. Disconnect and remove tube assemblies (1) and (2) from the diverter valve.2. Disconnect pilot hose assembly (3) at both ends and remove from the machine.3. Disconnect diverter solenoid electrical connector (4). 4. Disconnect and remove tube assembly (5) from the diverter valve.5. Disconnect pilot hose assembly (6) from the diverter valve. 6. Disconnect hose assemblies (7), (8) and (9) from the diverter valve. 7. Remove hose assemblies (10) and (11) from the diverter valve. 8. Remove the two bolts and washers that hold accumulator (ride control) rear clamp (12) to the front frame. Remove clamp (12) from the front frame. 9. Remove two bolts (13) and washers that hold the diverter valve to the front frame. 10. Remove diverter valve (14) from the front frame. Retain spacers (15), (17) and shims (16) (if equipped) from under the diverter valve. The weight of the diverter valve is 20 kg (44 lb).Install Diverter Valve
1. Check the condition of all O-ring seals. If any of the seals are worn or damaged, use new parts for replacement.2. Put the diverter valve in position in the front frame. The weight of the diverter valve is 20 kg (44 lb). 3. Put spacers (2), (4) and shims (3) (if equipped) in position under diverter valve (1) as shown. Install two bolts (5) and washers that hold the diverter valve to the front frame. 4. Put accumulator (ride control) rear clamp (6) in position on the front frame as shown. Install the two bolts and washers that hold clamp (6) to the front frame. 5. Connect hose assemblies (7) and (8) to the diverter valve. 6. Connect hose assemblies (9), (10) and (11) to the diverter valve. 7. Connect pilot hose assembly (13) to the diverter valve.8. Put tube assembly (12) in position on the diverter valve. Connect tube assembly (12) to the diverter valve. 9. Connect diverter solenoid electrical connector (17).10. Put pilot hose assembly (16) in position in the front frame. Connect pilot hose assembly (16) to the diverter valve and manifold (18).11. Put tube assemblies (14) and (15) in position on the diverter valve. Connect tube assemblies (14) and (15) to the diverter valve.End by:a. Install accumulator (ride control).b. Install main implement control valve.Disassemble & Assemble Diverter Valve
Start by:a. Remove diverter valve (ride control).1. Be sure the outside of the diverter valve is thoroughly clean prior to disassembly.
Typical Example2. Remove tube assembly (1) and the O-ring seals from the diverter valve.
Typical Example3. Remove shuttle valve (2) from the diverter valve body. 4. Remove two back-up rings (3) and O-ring seal (4) from the shuttle valve body. Remove two back-up rings (6) and O-ring seal (5) from the shuttle valve body. Remove O-ring seal (7) from the shuttle valve body. Remove ball (8) from the shuttle valve body.
Typical Example5. Remove locknut (9) and the washer. Remove coil assembly (10).
Typical Example6. Remove cartridge (11) from the diverter valve body. 7. Remove O-ring seals (12), (13) and (14) from the cartridge.
Typical Example 8. Remove
1. Check the condition of all O-ring seals. If any of the seals are worn or damaged, use new parts for replacement.2. Put the diverter valve in position in the front frame. The weight of the diverter valve is 20 kg (44 lb). 3. Put spacers (2), (4) and shims (3) (if equipped) in position under diverter valve (1) as shown. Install two bolts (5) and washers that hold the diverter valve to the front frame. 4. Put accumulator (ride control) rear clamp (6) in position on the front frame as shown. Install the two bolts and washers that hold clamp (6) to the front frame. 5. Connect hose assemblies (7) and (8) to the diverter valve. 6. Connect hose assemblies (9), (10) and (11) to the diverter valve. 7. Connect pilot hose assembly (13) to the diverter valve.8. Put tube assembly (12) in position on the diverter valve. Connect tube assembly (12) to the diverter valve. 9. Connect diverter solenoid electrical connector (17).10. Put pilot hose assembly (16) in position in the front frame. Connect pilot hose assembly (16) to the diverter valve and manifold (18).11. Put tube assemblies (14) and (15) in position on the diverter valve. Connect tube assemblies (14) and (15) to the diverter valve.End by:a. Install accumulator (ride control).b. Install main implement control valve.Disassemble & Assemble Diverter Valve
Start by:a. Remove diverter valve (ride control).1. Be sure the outside of the diverter valve is thoroughly clean prior to disassembly.
Typical Example2. Remove tube assembly (1) and the O-ring seals from the diverter valve.
Typical Example3. Remove shuttle valve (2) from the diverter valve body. 4. Remove two back-up rings (3) and O-ring seal (4) from the shuttle valve body. Remove two back-up rings (6) and O-ring seal (5) from the shuttle valve body. Remove O-ring seal (7) from the shuttle valve body. Remove ball (8) from the shuttle valve body.
Typical Example5. Remove locknut (9) and the washer. Remove coil assembly (10).
Typical Example6. Remove cartridge (11) from the diverter valve body. 7. Remove O-ring seals (12), (13) and (14) from the cartridge.
Typical Example 8. Remove
Parts tube Caterpillar catalog:
0550105
TUBE A
Caterpillar
Caterpillar
0550079
TUBE
Caterpillar
Caterpillar
0549857
TUBE A
Caterpillar
Caterpillar
0549856
TUBE A
Caterpillar
Caterpillar
0549853
TUBE A
Caterpillar
Caterpillar
0549852
TUBE A
Caterpillar
Caterpillar
0550154
TUBE A-BASIC
Caterpillar
Caterpillar
0550182
TUBE A
Caterpillar
Caterpillar
0550614
TUBE A
Caterpillar
Caterpillar
0550686
TUBE A
Caterpillar
Caterpillar
0550742
TUBE A-BASIC
Caterpillar
Caterpillar
0550746
TUBE A-BASIC
Caterpillar
Caterpillar