TUBE AS 1107453 - Caterpillar

Illustration 10 g00990497
(23) 226-7321 Gusset (24) 226-7322 Gusset (25) 226-7323 Gusset (L6) 10.0 mm (0.39 inch) (L7) 124.0 mm (4.88 inch) (L8) 43.0 mm (1.69 inch) gap in weld (L9) 61.0 mm (2.40 inch) gap in weld (W8) 5.0 mm (0.20 inch) fillet weld (W9) 5.0 mm (0.20 inch) fillet weld (W10) 5.0 mm (0.20 inch) fillet weld (W11) 5.0 mm (0.20 inch) bevel groove weldInstall four gussets (24). Weld (W8) is a 5.0 mm (0.20 inch) fillet weld. Each plate (24) is welded on two edges on one side. The two exterior plates receive weld (W8) on the outboard side of the gussets. The two interior plates receive weld (W8) on the inboard side of the gussets. There are eight welds (W8). Four upper welds (W8) are interrupted by gap (L9). Install two gussets (23). Weld (W9) is a 5.0 mm (0.20 inch) fillet weld. There are four welds (W9). All welds (W9) are on the outboard side of gussets (23). Two welds (W9) are interrupted by gap (L8). Install two gussets (25). Weld (W10) is a 5.0 mm (0.20 inch) fillet weld. Weld (W11) is a 5.0 mm (0.20 inch) bevel groove weld. Install Rear Plates and Strips
Illustration 11 g00990502
(22) 222-1120 Strip (26) 226-7324 Plate (L5) 50.0 - 150.0 mm (1.97 - 5.91 inch) (L10) 454.0 mm (17.87 inch) (L11) 393.0 mm (15.47 inch) (L12) 406.0 mm (15.98 inch) (L13) 64.0 mm (2.52 inch) (W12) 5.0 mm (0.20 inch) intermittent fillet weld (W13) 5.0 mm (0.20 inch) fillet weldInstall two strips (22). Weld (W12) is a 5.0 mm (0.20 inch) intermittent fillet weld. There must be 50.0 mm (1.97 inch) of weld in every 150.0 mm (5.91 inch).Install two plates (26). Weld (W13) is a 5.0 mm (0.20 inch) fillet weld. Weld (W13) is continuous around the entire perimeter of each plate.Install Skid Assemblies
Illustration 12 g01009065
(4) 2T-3041 Skid As (17) 219-6101 Plate (18) 219-6102 Plate (28) 226-7329 Plate (28A) Start of weld (W16) for the interior diameter (29) 226-7328 Skid As (L14) 170.0 mm (6.69 inch) (L15) 232.0 mm (9.13 inch) (L16) 131.0 mm (5.16 inch) (L17) 30.0 mm (1.18 inch) (W14) 5.0 mm (0.20 inch) fillet weld (W15) 5.0 mm (0.20 inch) bevel groove weld (W16) 5.0 mm (0.20 inch) fillet weldInstall two skid assemblies (29). Locate one skid assembly 170.0 mm (6.69 inch) (L14) inboard from the bent edge of plate (17). Locate the other skid assembly 170.0 mm (6.69 inch) (L14) inboard from the bent edge of plate (18). The tops of skid assemblies (29) must be 232.0 mm (9.13 inch) (L15) above the lower edge of plate (30). Weld (W14) is a 5.0 mm (0.20 inch) fillet weld. Weld (W15) is a 5.0 mm (0.20 inch) bevel groove weld.Install two skid assemblies (4). The tops of skid assemblies (4) must be 131.0 mm (5.16 inch) (L16) below the bottoms of skid assemblies (29) .Note: