1243226 TUBE AS-OIL GAUGE Caterpillar parts
3116, 322B L, 322B LN, 322C, 325B, 325B L, M325B
Rating:
Alternative (cross code) number:
CA1243226
124-3226
1243226
CA1243226
124-3226
1243226
Weight: 0.30 pounds 0 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 1243226:
Number on catalog scheme:
6
For full view, you need register
Caterpillar parts catalog:
Information:
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Never remove the fill/vent plug from the hydraulic tank if the oil is hot.Air can enter the system and cause pump damage.
Illustration 1 g02106374
Servicing position for a general forest machine
Illustration 2 g02106373
Servicing position for a log loader machine
Park the machine on level ground. Position the machine in the servicing position.
Open the access door on the right side of the machine.
Illustration 3 g02024082
(A) High temperature range
(B) Low temperature range
For a cold machine, maintain the hydraulic oil level in the low temperature range (B). For a machine that is at normal operating temperature, maintain the hydraulic oil level in the high temperature range (A).
Close the access door. Note: Perform Step 5 through Step 8 if the oil level is low.Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information that pertains to Containing Fluid Spillage.
Pressurized system!The hydraulic tank contains hot oil under pressure. To prevent burns from the sudden release of hot oil, relieve the tank pressure with the engine off by slowly turning the cap approximately 1/8 of a turn until the cap reaches the secondary stop.
Illustration 4 g02709964
Illustration 5 g02275615
Filler cap
(A) LOCK position
(B) PRESSURE RELEASE - START position
(C) PRESSURE RELEASE - END position
(D) OPEN position
Release the pressure that may be present in the return hydraulic circuit with the following procedure. Refer to Illustration 5 for filler cap positions.
Turn the filler cap counterclockwise and move the arrow from position (A) to position (B).
Release the pressure for a minimum of 45 seconds by moving the arrow from position (B) to position (C).
Push the filler cap down and move the arrow from position (C) to position (D).
After the tank pressure is relieved, remove the filler cap.
Add oil if necessary. See Operation and Maintenance, "Lubricant Viscosities"
Check the O-ring seal of the filler cap. Replace the O-ring seal if the O-ring seal is damaged.
Clean the filler cap. Tighten the filler cap on the hydraulic tank to position (A).
Parts tube Caterpillar catalog:
3116, 320 L, 320B, 613C II, E120B
1395121
TUBE AS
3412E
3412E
1364792
TUBE AS
3412E
3412E
1323584
TUBE AS
3412E
3412E
2110892
TUBE
3412E
3412E
2110891
TUBE AS
3412E
3412E
1315112
TUBE AS
3054, 3054B, 307, 312B L, 315B L, 554, AP-800C, BG-225B, BG-225C
3054, 3054B, 307, 312B L, 315B L, 554, AP-800C, BG-225B, BG-225C
3157685
TUBE
3054, 3054B, 3056
3054, 3054B, 3056
1292147
TUBE AS
3116, 320B, 322B, 322B L, 322B LN, 325B, 325B L, M325B
3116, 320B, 322B, 322B L, 322B LN, 325B, 325B L, M325B
1292146
TUBE AS
3116, 320B, 322B, 322B L, 322B LN, 325B, 325B L, 953C, 963C, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, CS-531D, CS-533D, CS-563D, CS-573D, CS-583D, M325B
3116, 320B, 322B, 322B L, 322B LN, 325B, 325B L, 953C, 963C, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, CS-531D, CS-533D, CS-563D, CS-573D, CS-583D, M325B
3114, 3116, 320 L, 320B, 322 FM L, 322B, 322B L, 322B LN, 322C, 322C FM, 325, 325 L, 325 LN, 325B, 325B L, CB-634C, CB-634D, M325B
3116, 320B, 322B, 322B L, 322B LN, 325B, 325B L, 953C, 963C, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, CS-531D, CS-533D, CS-563D, CS-573D, CS-583D, M325B