TUBE CLAMP, 1 1/4" 13088 - Caterpillar

13088 TUBE CLAMP, 1 1/4" Caterpillar parts PR-275

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA13088
1-3088
13088

Buy TUBE CLAMP, 1 1/4" 13088 Caterpillar genuine, new aftermarket tractor parts with delivery
COLD PLANER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Curt 13088 55361 45050 40002 21500 Class 3 Trailer Hitch Tow Package for Infiniti QX4 and Nissan Pathfinder

$373.79

30 Apr 2024

US: Trends Auto

Curt 13088 55361 45050 40002 21500 Class 3 Trailer Hitch Tow Package for Infiniti QX4 and Nissan Pathfinder

Replacement Go Cart Belt, Comet 203584, 203584A, 884-100

$19.99

08 Nov 2023
0.38[0.17] Pounds
US: ASC Auto Parts

Replacement Go Cart Belt, Comet 203584, 203584A, 884-100
Rotary Rotary Brand Part number 13088 || Aftermarket Replacement Parts || Sold & Shipped by Over The Hill Tractor || 034761130881 || Ship from Virginia

$27.98

07 Nov 2023
0.38[0.17] pounds
US: OMBWarehouse

Number on catalog scheme: 15

Caterpillar 13088 Parts scheme TUBE CLAMP, 1 1/4"

For full view, you need register

Compatible equipment models: 13088:

COLD PLANER PR-275 Caterpillar

Information:

Restoring Display Settings or Machine Settings
Use the "Restore Settings" dialog in order to restore the Display settings and/or Machine settings that have been previously saved. From this dialog, you can restore the full configuration settings of the Display. These settings may be stored in previously saved:
Display settings files
Machine settings filesBe sure to restore the correct Machine settings file for your machine. Display settings files can be used for any machine, regardless of type.Note: The Machine settings file contains the machine dimensions. Only use the Machine settings file on the same machine that the file was created on.Note: When you restore the Display settings and/or Machine settings, the GPS receiver configuration settings and the brightness settings of the Display are not changed.AccuGrade Systems are unable to restore the angle sensor calibration settings.The "Restore Settings" dialog lists the settings files on the data card.In order to access the "Restore Settings" dialog complete the following steps:
Be sure that a data card with the Settings files is inserted into the Display.
Illustration 1 g01300298
From the "Setup Menu - Configuration" dialog, press the Down arrow or the Up arrow until "Restore Settings" is highlighted.
Illustration 2 g01300299
Press the "OK" key.The "Restore Settings" dialog appears that lists the setting files that are on the data card.
Press the Down arrow or the Up arrow in order to select the settings file that you want.
Press the "OK" key in order to confirm the settings.In order to close the dialog without selecting a settings file, press the Escape Key. The "Restore Settings" dialog appears.If you attempt to restore an invalid settings file, a warning message appears.
Caterpillar recommends that you check the Blade Wear setting when you restore a Machine settings file. A dialog warns you to do this.
Press the "OK" key.
Depending on what was selected in the "Restore Settings" dialog, one of the messages shown in Table 1 will appear:
Table 1
Possible Messages
File Type Message
Display settings Restoring Display Settings. Please wait...
Machine settings Restoring Machine Settings. Please wait...
Press the Escape Key in order to go back to the "Setup Menu - Configuration" dialog. Press the Escape Key again in order to exit the "Setup Menu - Configuration" dialog. The changes take effect immediately.Always check the "Blade Wear" dialog. The machine cutting edge may have worn (or been renewed) since the Machine settings were saved.