AVSPARE.COM
parts catalog

TUBE AS 1400280 - Caterpillar



1400280 TUBE AS Caterpillar parts 330B L TUBE
Rating:
18
Alternative (cross code) number:
CA1400280
140-0280
1400280
Caterpillar 1400280 TUBE AS

Buy TUBE AS 1400280 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 1400280:

EXCAVATOR  330B L   Caterpillar
Number on catalog scheme: 18
 
  For full view, you need register

Information:

(21) Torque for eight bolts ... 60 4 N m (44 3 lb ft)Adjustment Of The Brake Mechanism
If the mechanism has been assembled with new parts, or shims (23) behind plate (22) have been lost, make the adjustment that follows:1. Install a 9.52 mm (.375 in) diameter rod through holes (C) in support assembly (17) and bell crank (18).2. Hold rear lever assembly (24) against stop (D) of the support assembly.3. Hold lever assemblies (25) apart to remove movement (slack) in the linkage.4. Measure distance (E) between right lever assembly (24) and plate (22) with a feeler gauge. Distance (E) must be ... 0.25 0.13 mm (.010 .005 in)5. Add or remove shims (23) between plate and support assembly to get correct distance (E).6. Remove the rod from holes (C).7. See Adjustment Of The Brakes.Adjustment Of The Brakes
1. Remove pins (3) from rod assemblies (4) and levers (11).2. Turn socket (15) clockwise until brake band (26) is tight on the brake drum. Then turn socket (15) counterclockwise one and one-half turns or nine clicks (the noise heard when a detent is felt).3. Check the length of rod assemblies (9). Distance (B) between the centers of the pins on each end of the rod assemblies must be about 1113 mm (43.8 in). Adjust the length of rod assemblies (9) if it is needed. Levers (16) will be in a vertical position when rod assemblies (9) are adjusted correctly.4. Adjust three vertical rods (2) so distance (A), from the pedals to the rear face of the dash, is 6.0 mm (.24 in). Make sure that vertical rods (2) are against stops (10) before a measurement is made.5. Move levers (11) as far to the rear of the machine as possible. Make sure brake bell cranks (13) are against steering bell cranks (14).6. Adjust rod assemblies (4) to the longest length that permits pins (3) to fit freely. Turn rod assemblies (4) one turn to make them shorter. Connect rod assemblies (4) to levers (11).7. Adjust rod assembly (1) so that pawl (8) engages ratchet (12) when the transmission lock lever is in the down position and both brakes are in the activated position (pedals are pushed down).8. Remove pins (7) from rod assemblies (5) and levers (6).9. Use rod assemblies (5) to push pawls (19) down until they come in contact with ratchet (20). With the transmission lock lever in the down position and both brakes in the activated position, adjust rod assemblies (5) to the longest length that permits pins (7) to fit freely. Connect rod assemblies (5) to levers (6).10. Make sure all lock nuts are tight.Adjustment Of The Steering Clutch Control Linkage
1. Make sure the pedals are adjusted correctly and rods (2) are against the stops.2. Remove pins (30) from rod assemblies (27) and levers (28).3. Move levers (28) down and toward the rear of the machine until they are against the stops.4. Adjust rod assemblies (27) to the longest length that permits

Caterpillar parts catalog:

Caterpillar parts catalog
330B L, 330B LN Excavators 3YR00001-UP (MACHINE) POWERED BY 3306 Engine
330B & 330B L Excavators 4RS00001-UP (MACHINE) POWERED BY 3306 Engine


Parts tube Caterpillar catalog:

8N7318 TUBE AS
120B, 120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C,...
8N7315 TUBE AS-OUTLET
120B, 120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C,...
2P1739 TUBE AS-PUMP
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 235, 235B, 235C, 330, 330 L, 3306, 3306B, 3306C, 330B, 330B L, 350, 528B, 530B, 545, 5...
4W9057 TUBE AS
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 235B, 330, 330 L, 3306, 3306B, 3306C, 330B, 330B L, 350, 528B, 530B, 545, 572G, 572R, ...
7X2049 TUBE AS-REFRIGERANT ORIFICE
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16H, 307B, 317B LN, 318B, 322B L, 325B L, 330B L, 345B, 34...
2378526 TUBE
305.5, 306, 306E, 307B, 307C, 307D, 308C, 311C, 312C, 312C L, 314C, 315C, 318C, 319C, 320B, 320C, 320C FM, 321C, 322B L, 322C, 325C, 330B L, 330C, 330C L, 330C MH, 345B II, 345B II MH, 345C, 345C L, 3...
5C4237 TUBE
215, 320B, 325 L, 325B L, 330B L, 345B L, 350, 350 L, 375, 5080
1319622 TUBE AS
330B, 330B L, W330B
1591055 TUBE AS
330B L, 330C, 330C L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.