2350860 TUBE Caterpillar parts
D6N
Rating:
Alternative (cross code) number:
CA2350860
235-0860
2350860
CA2350860
235-0860
2350860
Weight: 7 pounds 3 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 2350860:
Information:
Lead Numbering
Each coil lead is marked according to the following diagrams. The diagrams contained show the four, six, ten, and twelve lead configurations available in present day SR4 generators.The standard generator diagram and the terminal connections are on the nameplate of each generator.Numbering is clockwise from the top and from the outside inward.
4 Lead Wye Configuration
6 Lead Wye ConfigurationTerminal T4, T5 and T6 become the neutral connection when tied together in the 6 Lead Wye Configuration.
10 Lead Wye ConfigurationTerminal T0 is the neutral lead for the 4 lead and 10 lead generators.
12 Lead Wye ConfigurationTerminals T10, T11, and T12 become the neutral connection when tied together in the 12 Lead Wye Configuration.
12 Lead Delta ConfigurationIn the 12 Lead Delta Configuration Terminals T6 and T9 become the neutral connection when tied together and grounded, reflecting the Terminal T2, T10 connection as the high phase.Grounding the Frame
In any generator set installation, the frame of the generator must be positively connected to an earth ground or to the hull of a vessel. This connection is the first one made at installation, and the last one to be removed. If the generator set is on flexible or resilient pads, the ground connection must be flexible to avoid possible breakage in later operation.Ground connection cable or straps should have at least the current carrying capacity of the largest line lead to the connected load. Joints in cables or straps must be clean, free of electrical resistance, and protected from possible oxidation. Bolted ground connection joints eventually oxidize, and are frequent sources of radio frequency interference. Silver soldered, bolted joints are electrically and mechanically sound.Neutral Connections
"Y"-connected generators usually have the neutral grounded when the generator is installed unless definite measures are taken to prevent grounds on the load side. The grounding of the neutral is to prevent load side equipment damage.If the neutral wire is grounded and one of the phase leads becomes grounded, the excessive current will open a load circuit breaker or collapse the generator voltage. The result depends on the particular generator electrical characteristics, type of fault, and circuit breaker trip rating. An undervoltage device may be required to provide adequate short circuit protection.There are some instances in which it is undesirable to ground the neutral wire. In these applications where definite measures (ground fault protective circuits) have been taken to prevent grounds to the phase leads, an ungrounded generator neutral lead is acceptable.Ground fault protection requires that the entire group of distribution circuits be studied and treated as a system. The owner should engage a certified and registered consultant if a new distribution system is being developed, or if an existing system is to be modified for ground fault protection.Single Units
Four Wire: In a three phase, four wire system, the neutral wire should be grounded according to local wiring codes.In applications where definite measures are taken to prevent grounds to the load leads, an ungrounded neutral can be used. Be sure to check your local wiring codes.Multiple Units
Operation of multiple
Each coil lead is marked according to the following diagrams. The diagrams contained show the four, six, ten, and twelve lead configurations available in present day SR4 generators.The standard generator diagram and the terminal connections are on the nameplate of each generator.Numbering is clockwise from the top and from the outside inward.
4 Lead Wye Configuration
6 Lead Wye ConfigurationTerminal T4, T5 and T6 become the neutral connection when tied together in the 6 Lead Wye Configuration.
10 Lead Wye ConfigurationTerminal T0 is the neutral lead for the 4 lead and 10 lead generators.
12 Lead Wye ConfigurationTerminals T10, T11, and T12 become the neutral connection when tied together in the 12 Lead Wye Configuration.
12 Lead Delta ConfigurationIn the 12 Lead Delta Configuration Terminals T6 and T9 become the neutral connection when tied together and grounded, reflecting the Terminal T2, T10 connection as the high phase.Grounding the Frame
In any generator set installation, the frame of the generator must be positively connected to an earth ground or to the hull of a vessel. This connection is the first one made at installation, and the last one to be removed. If the generator set is on flexible or resilient pads, the ground connection must be flexible to avoid possible breakage in later operation.Ground connection cable or straps should have at least the current carrying capacity of the largest line lead to the connected load. Joints in cables or straps must be clean, free of electrical resistance, and protected from possible oxidation. Bolted ground connection joints eventually oxidize, and are frequent sources of radio frequency interference. Silver soldered, bolted joints are electrically and mechanically sound.Neutral Connections
"Y"-connected generators usually have the neutral grounded when the generator is installed unless definite measures are taken to prevent grounds on the load side. The grounding of the neutral is to prevent load side equipment damage.If the neutral wire is grounded and one of the phase leads becomes grounded, the excessive current will open a load circuit breaker or collapse the generator voltage. The result depends on the particular generator electrical characteristics, type of fault, and circuit breaker trip rating. An undervoltage device may be required to provide adequate short circuit protection.There are some instances in which it is undesirable to ground the neutral wire. In these applications where definite measures (ground fault protective circuits) have been taken to prevent grounds to the phase leads, an ungrounded generator neutral lead is acceptable.Ground fault protection requires that the entire group of distribution circuits be studied and treated as a system. The owner should engage a certified and registered consultant if a new distribution system is being developed, or if an existing system is to be modified for ground fault protection.Single Units
Four Wire: In a three phase, four wire system, the neutral wire should be grounded according to local wiring codes.In applications where definite measures are taken to prevent grounds to the load leads, an ungrounded neutral can be used. Be sure to check your local wiring codes.Multiple Units
Operation of multiple
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
8T2225
TUBE-HEAT SHRINK
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 236D, 242D, 246C, 246D, 24H, 256C, 257D, 259D, 262C, 262C2, 262D, 272C, 272D, ...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 236D, 242D, 246C, 246D, 24H, 256C, 257D, 259D, 262C, 262C2, 262D, 272C, 272D, ...
7X2049
TUBE AS-REFRIGERANT ORIFICE
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16H, 307B, 317B LN, 318B, 322B L, 325B L, 330B L, 345B, 34...
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16H, 307B, 317B LN, 318B, 322B L, 325B L, 330B L, 345B, 34...
1355970
TUBE AS-PISTON COOLING JET
30/30, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 35, 45, 525B, 533, 535B, 539, 543, 55, 550, 570, 570B, 574, 580, 580B, 938G, 938G II, 950G, 950G II, 962G, 962G II, C7, D5N, D6N, DEUCE, IT38G,...
30/30, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 35, 45, 525B, 533, 535B, 539, 543, 55, 550, 570, 570B, 574, 580, 580B, 938G, 938G II, 950G, 950G II, 962G, 962G II, C7, D5N, D6N, DEUCE, IT38G,...
2473755
TUBE AS
120H, 135H, 3126B, 322C, 322C FM, 325C, 325C FM, 561N, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
120H, 135H, 3126B, 322C, 322C FM, 325C, 325C FM, 561N, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
3368174
TUBE-FUEL INJECTION
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
3368175
TUBE-FUEL INJECTION
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
3368176
TUBE-FUEL INJECTION
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
3368177
TUBE-FUEL INJECTION
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
3368178
TUBE-FUEL INJECTION
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
3368179
TUBE-FUEL INJECTION
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
3368180
TUBE-FUEL INJECTION
120M, 12M, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-64, CS-74, D6K, D6K LGP, D6N, IT38H, M316D, M318D, M318D MH, M322D, ...
120M, 12M, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-64, CS-74, D6K, D6K LGP, D6N, IT38H, M316D, M318D, M318D MH, M322D, ...
3211270
TUBE-OIL
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
2334990
TUBE AS
D6N
D6N
2511904
TUBE AS
D6N
D6N
2311359
TUBE AS
D6N
D6N
1696172
TUBE AS
D6N
D6N
2971969
TUBE AS
D6N
D6N
2364112
TUBE AS
D6N
D6N
1726653
TUBE AS
D6N
D6N
1726650
TUBE AS
D6N
D6N
2830923
TUBE AS
D6N
D6N
2833345
TUBE AS
D6N
D6N
1761853
TUBE AS
D6N
D6N
1761852
TUBE AS
D6N
D6N